On the right side of the screen it is turning red and is not aligning properly looks like it is trying to go 3d. what could cause this?

Bad convergence board.

TV Parts Universal TV Stands DLP Chips ShopJimmy

the 3d effect is caused by a mis alignment of the tree tubes you probably have a broken FRAME holding the tubes in place so that HEAT or VIBRATION can move them and the alingment is off dont forget you have one tube for RED one for GREEN and the other for BLUE if they are not aligned properly they can look like a 3d pcture without 3d glasses ha! sorry for the bad grammer...

Good luck!

The phillips DPTV305 - DPTV345 convergence repair kit is the right kit for your model which should solve that issue. The kit is available from www.tvrepairworld.com and also contains the CD with instructions.

Projection TV sets have several common problems listed below.

Problem #1) Convergence

Symptoms:

• Screen Looks 3D
• Colors wont align
• Screen may look distorted
• No Audio/Video - TV makes a chirping sound.

Problem #2 CRT Fluid has clouded over. Symtoms

• Dull looking video
• White looking video
• Halos around objects
• Red/Orange looking video

You can see some examples and find a fix here...

http://www.fixya.com/support/r2861467-solution_video_looking_whiteish_dull

Projection TV sets have several common problems listed below.

Problem #1) Convergence

Symptoms:

• Screen Looks 3D
• Colors wont align
• Screen may look distorted
• No Audio/Video - TV makes a chirping sound.

Problem #2 CRT Fluid has clouded over. Symtoms

• Dull looking video
• White looking video
• Halos around objects
• Red/Orange looking video

You can see some examples and find a fix here...

http://www.fixya.com/support/r2861467-solution_video_looking_whiteish_dull

There are two common problems with these sets.

Problem #1) Convergence

Symptoms:

• Screen Looks 3D
• Colors wont align
• Video may look distorted

Problem #2 CRT Fluid has clouded over. Symtoms

• Dull looking video
• White looking video
• Halos around objects
• Red/Orange looking video

You can see some examples and find a fix here...

http://www.fixya.com/support/r2861467-solution_video_looking_whiteish_dull

There are two common problems with these sets.

Problem #1) Convergence

Symptoms:

• Screen Looks 3D
• Colors wont align
• Video may look distorted

Problem #2 CRT Fluid has clouded over. Symtoms

• Dull looking video
• White looking video
• Halos around objects
• Red/Orange looking video

You can see some examples and find a fix here...

http://www.fixya.com/support/r2861467-solution_video_looking_whiteish_dull

Projection TV sets are known to have two common problems. The first problem that is common to these sets is convergence failure. When this happens the TV will usually look 3D, Wavy/Distorted, etc. It may also shutdown and blink an error code.

The second common problem with Projection TV sets is dull video, halos around objects, white looking video, or red overpowers the screen. This is commonly caused by the fluid in the lens being clouded overs.

You can find more details and solutions here on Fixya at the following link below. Or click HERE


http://www.fixya.com/support/r2861467-solution_video_looking_whiteish_dull

You have a convergence problem. Here are some of the most common symptoms.
 
Screen looks 3D
One or more colors can't be adjusted when using the convergence menu. 
Screen is bowed in but stationary.

Here is a quick test....

Using your original remote go-to the tv settings then goto the convergence section.

Try to adjust the red and then the blue convergence.

You should be able to move them up, down, left, and right.

If you can't move them in all directions your convergence chips are bad and should be replaced. This is a common problem. 

>>>Solution<<<< 

You need to replace the convergence chips and convergence resistors. 

Check the site www.TvRepairKits.com. They have put together a kit for your exact model. The kit includes a photo instruction guide, original Sanyo STK chips, convergence resistors, etc. Everything you need to fix it yourself. 

Replace the convergence amps and test and replace any or all of the 2.2ohm resistors in the yoke return path out in front of the amps. This unit takes two STK392-110 Sanyo originals, DO NOT GET CHINESE KNOCK-OFFS... Buy them from Acme sales out of Florida and you can be assured they're originals.
Bill

William Rayburn, CET
Premium Technologies
PO Box 442
Long Beach, WA. 98631
360-642-4993