How do I change a bit - Milwaukee Tool Milwaukee 0824 24 v18 Hammer Drill Kit

You can't change the bits of the computer. The processor is set to run on a 64 bit or 32 bit operating system. Most home computers use the 32 bit operating system. It could be that the person reinstalled a 64 bit operating windows system in a 34 bit computer. If you have the operating system software and it is for 34 bit system it should install . Maybe the person changed the bios of the system the tells it where to boot from inorder to reboot from the disk. What computer do you have ? What op system are you using?

How and when:
With the power off & unplugged, loosen the collet and pull the bit out. if is is stuck, tap it gently with a piece of wood.
When installing the new bit, insert it fully into the collet and then withdraw it a couple mm. This will allow you to tap it loose later.

Leaving a bit in the router until next time is asking for a fused bit.

To change your Residential Gateway wireless settings:

1. Open a Web browser and type http://gateway.2wire.net or http://192.168.1.254; the 2Wire Home page opens.
   
   

   If the Home page does not open, check to make sure that you have no software firewalls blocking network access.
   

2. Click the Home Networking tab at the top of the 2Wire Home page.
   
3. Click EDIT SETTINGS located on the right panel (Status at a Glance) under the Wireless Settings heading.
   
4. Change your wireless settings and use the following information if you want to change to a custom WEP key.

   64-bit hexadecimal keys are exactly 10 characters in length. (For example, 123456789A is a valid string of 10 characters for 64-bit encryption.)
   

   128-bit hexadecimal keys are exactly 26 characters in length. (For example, 456FBCDF123400144445271730 is a valid string of 26 characters for 128-bit encryption.)
   

   64-bit ASCII keys are exactly 5 characters in length. (For example, GMODE is a valid string of 5 characters for 64-bit encryption)
   

   128-bit ASCII keys are exactly 13 characters in length (For example, 2008SUNSSWIN1 is a valid string of 13 characters for 128-bit encryption.)
   

Right-mouse click anywhere on the desktop "wallpaper".
Click Properties.
Click Settings.
Change from 16-bit or 24-bit to 32-bit.
Click Apply.

When you changed the WEP encryption from 64 bit to a stronger 128 bit encryption the encryption code gets changed and when you changes it back to 64 bit the new 64 bit encryption code will be different to the old 64 bit encryption code, that is why your laptops cannot connect to the router. The laptop wireless card needs to be configured with the new 64 bit encryption code before it can connect to the wireless router.
I suggest you configure the wireless router with WPA or WPA2 encryption, this is a much stronger encryption method than the old WEP encryption.
To secure your wireless network from unauthorized access, please click on this link and follow my instructions :-
http://www.fixya.com/support/r3559128-wireless_router_security

Right click on the free space in the desktop and select properties. Then go to display properties and change settings to 32 Bit and Change the screen resolution to 1024 by 768 Pixels.

Simply reinstall the OS (Operating System) and select 32 Bit this time.

On my older Sears router there is a lever on the base near the collet nut that you slide to engage the motor shaft to lock the motor shaft for bit changes. On newer models you may have a button or different mechanism to lock the shaft. After the shaft is locked you can use a small wrench to loosen the collet nut, usually by turning it counter-clockwise (viewed from the base). Once the nut is loose the bit should slide out (sometimes the bit is stuck in the collet and the nut may need to come all the way off to get them apart). Just replace the bit with a new bit with the same shaft diameter, tighten the nut, and you are set. If the new bit has a different shaft diameter than the old bit you may need to change the collet also (in general, different collets are used with different bit shaft diameters).

loosen the nut that holds the bit and sometimes you have to drive the bit into the router a little to get the collet to release.

to change the tray that reports print from
it can be changed in service mode soft switch 323
change bit 7 to a 1 to print from tray 1
change bit 6 to a 1 to print from tray 2
bit 5 to 1 to print from tray 3
bit 4 to 1 to print from tray 4
bit 3 to 1 to print from bypass tray