Where is the HO2S Bank 2 Sensor 1 located? On the Drivers side or the passenger side od engine? On the Ford 4.2 L

Four .
Heated Oxygen Sensor (HO2S Bank 1 Position 1)
Located in RH front pipe of the exhaust catalytic converter
--
Engine Controls Connector End Views in Engine Controls
Heated Oxygen Sensor (HO2S Bank 1 Position 2)
Located in RH rear pipe of the exhaust catalytic converter
--
Engine Controls Connector End Views in Engine Controls
Heated Oxygen Sensor (HO2S Bank 2 Position 1)
Located in LH front pipe of the exhaust catalytic converter
--
Engine Controls Connector End Views in Engine Controls
Heated Oxygen Sensor (HO2S Bank 2 Position 2)
Located in LH rear pipe of the exhaust catalytic converter

Hi there:

There are 2 up stream HO2S sensors, Bank 1, passenger side and Bank 2 drivers side.
You can find eaither on in the exhaust pipe about 6 inches from where the pipe hooks to the exhaust manifold on each side.




Hope this helps; also keep in mind that your feedback is important and I`ll appreciate your time and consideration if you leave some testimonial comment about this answer.

Thank you for using FixYa, have a nice day.

Oxygen sensors are always numbered like this:

Bank 1 sensor 1
Bank 2 sensor 1
Bank 1 sensor 2
Bank 2 sensor 2

some manufacturers use a kind of shorthand that reads different, but means the same thing:
Sensor 1/1 or O2s 1/1
Sensor 2/1 or O2s 2/1
Sensor 1/2 or O2s 1/2
Sensor 2/2 or O2s 2/2

Bank 1 is always the side of the engine where cylinder number 1 is located and, of coarse, Bank 2 is the opposite side.
On a 4 cylinder engine, there is only 1 bank and it is always referred to as Bank 1.

Sensor 1 is always the upstream sensor (The one located BEFORE the catalytic converter)
Sensor 2 is always the downstream sensor (the one that is located AFTER the catalytic converter.

Most GM engines have #1 cylinder located on the left bank, (or Driver's Side) of the engine,

HiI!!
6 cyl. and 8 cyl. engines are divided into 2 Banks, standing in front of the Engine, the Bank 1 is the side where the #1 spark plug is (on V6 Ford Engines is on the PASSENGER SIDE). Bank 2 is on the DRIVERS SIDE.
Check the following diagram for HO2 sensor locations (This diagram applies to Ranger, Explorer and Mountaineer models) :



2 would be Bank 1 and 2A would be Bank 2.
Good Luck!! A HELPFUL - 4 THUMBS - rating for this solution would be greatly appreciated. Thank you for using FixYa.

bank 1 is the passenger side and the number 2 o2 sensor or refereed to as the down stream sensor is located after the catalytic converter. heres a picture to aid you. hope this helps

Bank 2 means the drivers side, and sensor 1 is the upstream sensor. I believe sensor 1 is located before the cat. converter, and sensor 2 is located after

To retrieve OBDII Error codes from your Chrysler/Jeep/Dodge vehicle, do the following sequence with the key: ON-ACC-ON-ACC-ON and look at the odometer, that is where codes will be displayed. Here are the codes that you may/can get.

Ho2S = heated oxyen sensor, TP = throttle position, MAF = mass airflow, MAP = manifold absolute pressure, TC=turbocharger.P0030 HO2S Heater Control Circuit Bank 1 Sensor 1
P0031 HO2S Heater Circuit Low Voltage Bank 1 Sensor 1
P0032 HO2S Heater Circuit High Voltage Bank 1 Sensor 1
P0036 HO2S Heater Control Circuit Bank 1 Sensor 2
P0037 HO2S Heater Circuit Low Voltage Bank 1 Sensor 2
P0038 HO2S Heater Circuit High Voltage Bank 1 Sensor 2
P0050 HO2S Heater Circuit Bank 2 Sensor 1
P0051 HO2S Heater Circuit Low Voltage Bank 2 Sensor 1
P0052 HO2S Heater Circuit High Voltage Bank 2 Sensor 1
P0056 HO2S Heater Circuit Bank 2 Sensor 2
P0057 HO2S Heater Circuit Low Voltage Bank 2 Sensor 2
P0058 HO2S Heater Circuit High Voltage Bank 2 Sensor 2
P0100 MAF Sensor Ckt. Insufficient Activity
P0101 Mass Air Flow (MAF) Sensor Performance
P0102 Mass Air Flow (MAF) Sensor Circuit Low Frequency
P0103 Mass Air Flow (MAF) Sensor Circuit High Frequency
P0104 Mass Air Flow Circuit Intermittent
P0105 MAP Sensor Circuit Insufficient Activity
P0106 Manifold Absolute Pressure (MAP) System Performance
P0107 Manifold Absolute Pressure (MAP) Sensor Circuit Low Voltage
P0108 Manifold Absolute Pressure (MAP) Sensor Circuit High Voltage
P0109 Manifold Absolute Pressure Circuit Intermittent
P0110 Intake Air Temperature (IAT) Sensor Circuit
P0111 Intake Air Temperature (IAT) Sensor Performance
P0112 Intake Air Temperature (IAT) Sensor Circuit Low Voltage
P0113 Intake Air Temperature (IAT) Sensor Circuit High Voltage
P0114 Intake Air Temperature Circuit Intermittent
P0115 Engine Coolant Temperature (ECT) Sensor Circuit
P0116 Engine Coolant Temperature (ECT) Sensor Performance
P0117 Engine Coolant Temperature (ECT) Sensor Circuit Low Voltage
P0118 Engine Coolant Temperature (ECT) Sensor Circuit High Voltage
P0119 Engine Coolant Temperature Circuit Intermittent
P0120 Throttle Position System Performance
P0121 Throttle Position Sensor Circuit Insufficient Activity
P0122 Throttle Position (TP) Sensor Circuit Low Voltage
P0123 Throttle Position (TP) Sensor Circuit High Voltage
P0124 Throttle Position Sensor 1 Circuit Intermittent
P0125 Engine Coolant Temperature (ECT) Insufficient for Closed Loop Fuel Control
P0126 Insufficient Engine Coolant Temperature for Stable Operation
P0128 Coolant Thermostat
P0130 HO2S Circuit Closed Loop (CL) Performance Bank 1 Sensor 1
P0131 HO2S Circuit Low Voltage Bank 1 Sensor 1
P0132 HO2S Circuit High Voltage Bank 1 Sensor 1
P0133 HO2S Slow Response Bank 1 Sensor 1
P0134 HO2S Circuit Insufficient Activity Bank 1 Sensor 1
P0135 HO2S Heater Performance Bank 1 Sensor 1
P0136 HO2S Circuit Bank 1 Sensor 2
P0137 HO2S Circuit Low Voltage Bank 1 Sensor 2
P0138 HO2S Circuit High Voltage Bank 1 Sensor 2
P0139 HO2S Slow Response Bank 1 Sensor 2
P0140 HO2S Circuit Insufficient Activity Bank 1 Sensor 2
P0141 HO2S Heater Performance Bank 1 Sensor 2
P0142 HO2S Circuit Bank 1 Sensor 3
P0143 HO2S Circuit Low Voltage Bank 1 Sensor 3
P0144 HO2S Circuit High Voltage Bank 1 Sensor 3
P0145 HO2S Circuit Bank 1 Sensor 2 Slow Response
P0146 HO2S Circuit Insufficient Activity Bank 1 Sensor 3
P0147 HO2S Heater Performance Bank 1 Sensor 3
P0150 HO2S Circuit Closed Loop (CL) Performance Bank 2 Sensor 1
P0150 HO2S Circuit Bank 2 Sensor 1
P0151 HO2S Circuit Low Voltage Bank 2 Sensor 1
P0152 HO2S Circuit High Voltage Bank 2 Sensor 1
P0153 HO2S Slow Response Bank 2 Sensor 1
P0154 HO2S Circuit Insufficient Activity Bank 2 Sensor 1
P0155 HO2S Heater Performance Bank 2 Sensor 1
P0156 HO2S Circuit Bank 2 Sensor 2
P0157 HO2S Circuit Low Voltage Bank 2 Sensor 2
P0158 HO2S Circuit High Voltage Bank 2 Sensor 2
P0159 HO2S Slow Response Bank 2 Sensor 2
P0160 HO2S Circuit Insufficient Activity Bank 2 Sensor 2
P0161 HO2S Heater Performance Bank 2 Sensor 2
P0162 HO2S Circuit Bank 2 Sensor 3
P0163 HO2S Circuit Bank 2 Sensor 3 Low Voltage
P0164 HO2S Circuit Bank 2 Sensor 3 High Voltage


P

1998 Ford Truck Windstar 3.8L SFI 6cyl, there are 4 oxygen sensors on the Windstars They are divided into 2 banks of 2. Bank 1 is the for the rear 3 cylinders of the engine - Bank 2 is for the front 3 cylinders. Bank 1 / Sensor 1 (upstream) is located just below, in the pipe, the exhaust manifold on the back of the engine.

REMOVE TIP: you may have to bend part of the transmission heat shield out of the way - be sure to put it back when done.
Bank 1 Sensor 2 (downstream) is located just past the drivers side catalytic converter.
Bank 2 Sensor 1 (upstream) is located just below the exhaust manifold, in the pipe, at the front of the van - access is from the top.
Bank 2 Sensor 2 (downstream) sensor is located just past the passenger side catalytic converter.

NOTES: * Use lots of penetrating oil - allow to soak - to make removal easier and avoid damaging the exhaust pipe

Hope this help; TY for using Fixya (remember rated and comment this).

bank 1 on a chevy is on the drivers side youll have 4 O2 sensors sensor 1 bank 1 is on the engine side of the cat converter sensor 2 bank 1 is after the cat converter (drivers side )
bank 2 is on the passenger side sensor 1 is pre cat sensor 2 is post cat converter