Whirlpool front loading duet washer stops at the rinse/spin cycle door then locks. code F31 comes up. would this have something to do with the main board?

Whirlpool Duet GHW9150P Front Load Washer Beeping ...

www.fixya.com > ... > Whirlpool Duet GHW9150P Front Load Washer

Question about Whirlpool duet Washing Machines ... my front loader is not workingwhirlpool washer flashes and beeps will not finish a cycle 1 Beep/E10--Error: Water... It beeps through the wash and rinse cycle every couple of minutes. ... Cycle signal which tells you that the cycle is complete beeps through the entire cycle.

[PDF]front-loading automatic washer use and care ... - Whirlpool

www.whirlpool.com/.../U...

Translate this page Whirlpool Home AppliancesWash. This is the main portion of the wash cycle. You will see the washer tumble the load. ... Spin cycle. If the laundry is still wet, take half of the load out of the washer and try again. .... Using recommended AFFRESH® washer cleaner, add.

[PDF]DISHWASHER USER INSTRUCTIONS - Whirlpool

https://www.whirlpool.co...

Translate this page Whirlpool Home AppliancesThe first cycle using the sensor will run longer to calibrate the optical sensor. Rinse Aid. Using rinse aid will optimize your drying and wash performance. This dishwasher is ...... laundry detergent, hand soap, or dish detergent for hand washing .... models) you will experience more starts and stops throughout the entire cycle.

Continuous Beeping - Whirlpool Duet Sport Washer - The ...

appliantology.org > ... > The Laundry Appliance Repair Forum

dirt or faulty inlet solenoid diaphragm
simple fix is to turn the tap off at the wall when finished

those have a 2 latch system, sounds like the second latch that engages during the spin cycle never quite completed the safety lock , you could try and jumper the latch to see if that would release it, But it seems the secondary latch wasn't working properly in the first place, even the heaviest loads shouldn't pop the door open,

This washer will stop and start a number of times during fill as it is sensing how much water it needs. Also you must hook both water line up and have both on. Also you must use HE soap and very little of it.

Hi,
The following list of codes indicates an electronics communication problem with the washer:
Duet HT® washer - F01, F03, F06, F11, F23, F24, F27, F28, F29, F30, F31, F32, F35, F42, F61, F62, F63, F64, F65, F70, F71, and F99
Duet® washer - F05, F07, F09, F10, F11, F13, F14, F15, F21, F22, and FdU
Duet SportTM washer - F01, F11, F23, F24, F27, F28, F29, F30, F31, and F33
PLACEHOLDER FOR ART
To remove the error display, press Pause/Cancel twice.
If Pause/Cancel does not work:

1. Unplug washer or disconnect power for one minute.
2. Plug in washer or reconnect power.
3. Re-select the cycle and press Start.

NOTE: If the error remains on the display, then call for service.

Take care

Your problem could be one of the following:

* electronic control board

* door lock/switch assembly

Contact an appliance service company.

E47, no spin.
Replace the door lock.
To learn more about your washing machine, or to order parts, click here.
Related Posts:

• How to Replace the Door Switch on a Whirlpool Duet or Kenmore HE3t (and HE4t) Front Loading Washing Machine
• ddo Error Code on a Frigidaire Front Loading Washer
• Frigidaire Affinity Front Loading Washer Error Codes
• Whirlpool Duet Washer Door Latch Stuck in Lock Position; Washer Repair
• Replacing the Door Latch Assembly in a Kenmore / Frigidaire Front Loading Washing Machine

have you checked the belt to see if it came off or maybe broke off,if its not the belt then maybe the motor whent bad or needs reset,that just some of the possibilitys you might want to check,some motors have a reset butten on thim

I hope that you have a serivce contract or something on this unit you need a main control board f11 means that there is communication error between the 2 computer boards the fdl means that there is is door lock problem. But that is incorrect that is how you know which board has the problem the door lock is controlled by the main computer board. it's just playing tricks on you I have tried changing the door lock with those codes and it did nothing. that board tends to be alittle pricey .good luck.

try removing the bottom front panel and see if there is something blocking the drain.