- If you need clarification, ask it in the comment box above.
- Better answers use proper spelling and grammar.
- Provide details, support with references or personal experience.
Tell us some more! Your answer needs to include more details to help people.You can't post answers that contain an email address.Please enter a valid email address.The email address entered is already associated to an account.Login to postPlease use English characters only.
Tip: The max point reward for answering a question is 15.
remove all the ink cartridges, and then unplug the power cord from the back of the printer.
Now, hold down # and number 6 button together, and while holding them down, plug the power back in.
release the hold after about 30 seconds, or the display saying nvram reset .. something like that .. If the printer turns off , then you will have to turn it ON again .. and then insert the ink cartridges ,
this will reset the machine.. and should resolve the issue. Also check if yu have any old cartridge and first insert that and see. if no error on inserting the old cartridge and that if it come by inserting the new on, then it could be the cartridge problem. Will have to try with new ink cartridge.
How to Reset an HP Inkjet Cartridge
Hi there
Instructions Things You'll Need: Adhesive tape HP inkjet cartridge can be refilled easily, getting it to work again in the printer is another matter. The contacts on the back of the cartridge are programmed to read the ink level, but they don't reset for the printer just because you add more ink. You must get the printer to recognize the cartridge as new. You can do this easily if you have two other old cartridges, or you can manipulate the contacts on the refilled cartridge. Step 1 Insert the cartridge you refilled into the HP Printer. Have the printer print an alignment page, thus recognizing the cartridge. The printer will still read the ink level as where it was before you refilled it. Step 2 Remove the cartridge from the printer and replace it with another old cartridge. Have the printer print an alignment page with this cartridge so it recognizes it as a different cartridge from the first one. Step 3 Replace the second cartridge with a third one and run the same alignment page. Because the printer only retains the memory of two
Print Cartridges, it will erase the memory of the first (refilled) cartridge. Step 4 Insert the refilled cartridge into the printer. The printer will now recognize the cartridge as being full. Next Steps Step 1 Tape over the contact squares on the top left corner of the cartridge's contacts. Insert the cartridge into the printer and run an alignment page. Ignore any messages that might appear saying there is a problem with the cartridge. Step 2 Take the cartridge out of the printer. Remove the tape from the left corner and tape over the contact squares on the top right corner. Place the cartridge backs in and run another alignment page. Step 3 Remove and reinsert the cartridge, this time with no tape on any of the contacts. Check to see if the printer recognizes the cartridge as being full. Step 4 Repeat the above steps if the cartridge is still shown as being empty. This time, use the bottom corner contact squares instead of the top ones. If you are still unable to reset the cartridges, using multiple cartridges is likely the only way to do it.
jQuery('.article ol .image').each(function(i,e){
var $this = jQuery(this);
$this.find('img').error(function(){
jQuery(this).remove();
$this.remove();
});
});
All I ask is to call back and just gave a vote, it will gave me some satisfaction to know am helping some one, so I will keep on helping.
All The Best: Pineworks
As per the information you have provided, I understand that you are receiving an error "Remove and check black ink cartridge" on the All-In-One display screen. If yes, perform the below steps.
Let me provide you the cause of the issue. The most cause of the issue is that if you are using refilled, re manufacture ink cartridges, cartridge is not fitting properly, wrong cartridge no. However, perform the below steps to resolve the issue.
1. Remove the print cartridges from the printer. 2. Clean the print cartridges using the lint free cloth both the cartridges heads as well as inside the printer. 3.Follow the steps below to power cycle your
all-in-one:
a. Verify that the unit is switched on. Disconnect power
cable from All-in-One and also from wall outlet. b. Wait 30 seconds. c.
Plug in the power cable to All-in-One and also to wall outlet.
4. Insert only the black ink cartridge first and check the message on the printer.
If the issue is with the black ink cartridge then the same message will be appears on the printer. If not it will prompt you to insert the color ink cartridge.
Do the same procedure with the color ink cartridge.
If the issue persist, then it shows that the issue is with the black ink cartridge. check the expiry date of the print cartridges and try to replace it.
I believe the issue is with the printer itself. However, the printer using the HP 56 and 57 ink cartridges.
As you have mentioned that you have already replaced the black ink cartridge. Then it confirms that the issue is with the printer. However, you can try resetting of the printer to its default settings and check for the issue.
To reset the printer, perform the below steps.
A semi-full reset will do the following: The user settings to the factory
defaults, Language and country settings on some models, Fax logs, Fax headers,
Fax speed dial information.
Reset the All-in-One to the factory default
settings by using these instructions:
1. Unplug the power cable from
printer when the printer is powered on and wait for 20 seconds.
2. Then,
press and hold # and 6 while plugging in the power cord.
Continue holding
until it displays Semi Full Reset message in the front panel of the
All-in-One.
The printer might be turned off after performing the above steps, so no need to worry about that.
Then turn on the printer and check for the result.
Reset the All-in-One to the factory default settings by using these instructions: 1) Press Red Eye Removal & Print Photos button simultaneously 2)Enter Special Key Combo is displayed on the screen. Press and release in sequence "Red Eye Removal", "Print Photos", "Red Eye Removal" Display should say "Support" and display the FW rev XXXXX. 3) Press Right Arrow button until "Reset Menu" is displayed. Press OK. 4) Press Right arrow until "Semi full Reset" is displayed. 5) Press OK. Now, check the functionality of the All-in-One. If I could be of further assistance, let me know. If this helps or solves the issue, please rate it. Thanks, Joe
IssueAn 0xc18xxxxx or 0xc19xxxxx ink system error code displays on the front panel. The printer cannot copy, receive faxes, or print. Solution Press the On button to turn the printer off. Unplug the power cord from the back of the printer. Remove all the ink cartridges. Wait two minutes. Plug the power cord into the back of the printer. Press the On button to turn the printer on. Install the ink cartridges when prompted. If the error code does not display, the issue is resolved. If the 0xc18xxxxx or 0xc19xxxxx ink system error code displays on the front panel, service the printer.
I had this "Cartridge error" problem on my HP J5780 printer. Replaced
the cartridge, but still got the same error. Then removed the cartridge
and used a cotton swab with a little denatured alcohol, and gently and
carefully cleaned the contacts in the printer. Followed this with a dry
swab to be sure no alcohol left. Replaced the original cartridge, and
have been using it for a week now with no more error message.
HP, in order to sell more ink, monitors the expiration date of the cartridges installed. Solution is either to buy a new unexpired cartridge from HP or to disable the date monitoring built in to the printer. This latter is done by removing the button cell located inside the D135 printer on the left hand side or by simply slipping a thin piece of plastic between button cell and metal contact. You will no longer have date function on printer, but it won't object to expired cartridges either.
hi just fixed my 6110 hp by pulling out spring wire that is on right hand side where black ink cartridge gets inserted i think it was preventing a good contact
i did this after following all other help hints including cleaning heads etc and replacing with new ink now it works perfect hope this works for you too
×