Question about Kenmore Washing Machines

1 Answer

I need the installations instructions for a Kenmore washer Mod 11020882990 for the lid switch Stella

Posted by on

  • Anonymous Mar 28, 2014

    can not get center loose . there are 4 spring tabs on shaft. i have them bushed in . still can not get drum loose.

×

Ad

1 Answer

  • Level 3:

    An expert who has achieved level 3 by getting 1000 points

    All-Star:

    An expert that got 10 achievements.

    MVP:

    An expert that got 5 achievements.

    President:

    An expert whose answer got voted for 500 times.

  • Master
  • 1,937 Answers

This assumes that you have a basic Kenmore / Whirlpool top load, direct drive, neutral drain (it doesn't spin until the pump removes most of the water) machine.

First, see the Sears parts site for your washer:

http://www.searspartsdirect.com/partsdirect/part-model/Kenmore-Parts/Washer-Parts/Model-11020882990/0582/0153200?pathTaken=

and you'll see a list of major sub-components with diagrams and parts.

Newer model Whirlpool / Kenmore washers use a Lid Switch as a safety device. Unless the switch senses that the lid on the washer is closed, the washer will neither agitate nor spin.

Older models only used the switch during the spin cycle.

Try to bypass the Lid Switch by removing the Console and jumping the two outermost pins on the switch.

This is a Whirlpool PDF on how these washers operate. It has a diagram on jumping the switch as well as a detailed section on how the transmission works.

https://secured.whirlpool.com/Service/SrvTechAdm.nsf/2cd44500d572193285256a45004fd9d6/f7e2147fa98b28cf85257122007475cb/$FILE/L-55.pdf


It also has a troubleshooting guide.

To bypass the switch, you only have to disconnect the power to the washer, tilt the console back, unplug the switch and using an short piece of insulated wire, jump the two outermost contacts on the connector coming from the console and plug the washer back in.

Following is a description of how to gain access to the console and how to remove the cabinet if necessary.

http://www.american-appliance.com/catalog/newsdesk_info.php?newsPath=16&newsdesk_id=131&osCsid=913ba652cd504fb162f87d892bcb427b

With the jumper in place, try to re-start the washer.

If it works, the Lid Switch is a relatively inexpensive part and only requires you to access the console and remove the cabinet.

Posted on Oct 26, 2010

Ad

1 Suggested Answer

6ya6ya

6ya staff

  • 2 Answers

SOURCE:

Hi there,
Save hours of searching online or wasting money on unnecessary repairs by talking to a 6YA Expert who can help you resolve this issue over the phone in a minute or two.

Best thing about this new service is that you are never placed on hold and get to talk to real repairmen in the US.

Here's a link to this great service

Good luck!

Posted on Jan 02, 2017

Ad

Add Your Answer

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

1 Answer

My Kenmore Washer model: 110.49962603 stops during the rinse cylce. All the buttons were turned off after one cycle except the time button. It displays F28 on Time Estimated Remaining button. How can I fix...


By what you have stated, it sounds like a lid switch failure. The lid switch has to be closed for the drain and spin cycle on your washer. If the lid switch is faulty, it will act as if the lid is not closed. On this model, make sure the lid hinge screws are tight. If the screws are loose, the hinge might not activate the lid switch.

A quick check you can do is to jump the lid switch and see if it will drain. If the washer operates, the lid switch needs to be replaced.

To jump the lid switch you need to unplug the washer and open the console. I have provided you with the instructions for opening the console below. Once you have the console open, locate the connector for the lid switch. Place an insulated jumper between the gray and tan wires. Not the green it is a ground and will cause a short. After inserting the jumper make sure it will not touch anything metal, plug the washer in. Start the washer in a drain cycle. If the washer drains and spins, you need to replace the lid switch. Do not leave the jumper in while you are waiting for the part. The jumper is only of the test.

To you replace the lid switch you have to remove the cabinet of the washer. The instructions for that are also in the image below. Once the cabinet is removed you can take the screws out securing the lid switch and remove the harness from the clips along the underside of the cabinet. Then reinstall the lid switch in the reverse order. Before you reassemble the cabinet, please read the instructions for installing the cabinet provided in the image.

I hope this is helpful. Please reply below if you need further assistance.

Jan 23, 2018 | Kenmore HE2 Plus Front Load Washer

1 Answer

My Kenmore washer will fill with water and oscilate, then nothingf won't spin or drain. I 'm guessing that it is the lid switch , ( relay switch ) ?? Mod # 110.94518201 serial # VLG 1601709 can this...


This assumes that you have a basic Kenmore / Whirlpool top load, direct drive, neutral drain (it doesn't spin until the pump removes most of the water) machine.

First, see the Sears parts site for your washer:

http://www.searspartsdirect.com/partsdirect/part-model/Kenmore-Parts/Washer-Parts/Model-11094518201/0582/0153200?pathTaken=

and you'll see a list of major sub-components with diagrams and parts.

Look at the diagrams for the cabinet and you'll see a list of component parts (Lid Switch) with the Sears part numbers (the manufacturer authorized substitute numbers are Whirlpool) and the Sears price.

Newer model Whirlpool / Kenmore washers use a Lid Switch as a safety device. Unless the switch senses that the lid on the washer is closed, the washer will neither agitate nor spin.

Older models only used the switch during the spin cycle.

Try to bypass the Lid Switch by removing the Console and jumping the two outermost pins on the switch.


To bypass the switch, you only have to disconnect the power to the washer, tilt the console back, unplug the switch and using an short piece of insulated wire, jump the two outermost contacts on the connector coming from the console and plug the washer back in.

Following is a description of how to gain access to the console and how to remove the cabinet if necessary.

http://www.american-appliance.com/catalog/newsdesk_info.php?newsPath=16&newsdesk_id=131&osCsid=913ba652cd504fb162f87d892bcb427b

With the jumper in place, try to re-start the washer.

If it works, the Lid Switch is a relatively inexpensive part and only requires you to access the console and remove the cabinet.

Dec 03, 2010 | Washing Machines

1 Answer

Mod. 110.29852992 80 series will not pump out


This assumes that you have a basic Kenmore / Whirlpool top load, direct drive, neutral drain (it doesn't spin until the pump removes most of the water) machine.

First, see the Sears parts site for your washer:

http://www.searspartsdirect.com/partsdirect/getModel!retrieve.pd?modelNumber=110.29852992&pathTaken=partSearch

and you'll see a list of major sub-components with diagrams and parts.

If it neither drains nor spins, the first thing to check is the Lid Switch. This prevents the machine from draining and spinning if the lid is open.

I assume that you cannot hear the motor trying to turn.

See the following for how to access the console and Lid Switch connection.

http://www.american-appliance.com/catalog/newsdesk_info.php?newsPath=16&newsdesk_id=131&osCsid=6f8112b458c05fcc8f6d1a4139b9a723

Following is a Whirlpool installation and maintenance PDF on top load, direct drive washers. It has a description of how to by-pass the switch.

It also has a troubleshooting guide.

https://secured.whirlpool.com/Service/SrvTechAdm.nsf/2cd44500d572193285256a45004fd9d6/f7e2147fa98b28cf85257122007475cb/$FILE/L-55.pdf

To bypass the switch, you only have to disconnect the power to the washer, remove the two plastic clips from the console, remove the two screws under the clips,pull the console forward and tilt the console back, unplug the switch and using an short piece of insulated wire, jump the two outermost contacts on the connector coming from the console and plug the washer back in.

With the jumper in place, try to re-start the washer.

If it works, the Lid Switch is a relatively inexpensive part.

May 12, 2010 | Kenmore Washing Machines

1 Answer

Kenmore mod 23832100 Lid Switch broken HOw do I


Good day,
There are 3 different style lid switches used on Whirlpool/Kenmore washers. You have to break down the unit to determine which one you use. Any appliance parts house will carry what you need.
Here is an excellent tutorial.

http://www.youtube.com/watch?v=fC8SY3cU1Yc

Mar 01, 2010 | Kenmore 23822 Top Load Washer

2 Answers

I need help replacing my switch lid on my Kenmore 70 Series mod. # 110-22722100 Washer. Can anyone help me with this??


if you have a gray switch than you nead to bypass the switch.if you replace the switch it will brake again.you do not nead a door switch.

Jan 16, 2010 | Kenmore 24032\24036 Top Load Washer

1 Answer

Replace lid switch on a Kenmore washer


Sometimes on these you need to open the lid, remove the screws there first, then take the screws off the back. Try that.

Aug 06, 2009 | Kenmore 24032\24036 Top Load Washer

1 Answer

Kenmore 80 series mod 110225842400 stopped working during cycle. Tub won't drain and will not agitate.


Hi, When the washer is in spin or wash cyles, do you here any motor noises? It sounds like the lid switch might be bad. Sometimes you can actually see if the lid switch is broke or not. Please let me know if The lid switch appears to be the problem or if I can assist you further.

Vic

Jun 20, 2009 | Kenmore 20172 Top Load Washer

1 Answer

Kenmore stackable mod number 417.94802301


check your lid switch. if your lid swith is bad, it will fill and agitate, but will not pump or spin. therefore it will not go into rinse cycle without being able to pump out water. some lid swithes control the agitation also (usually frigidaire and older maytags), but i doubt yours does. you can check the lid switch for continuity while opening and closing the lid with a meter

Apr 30, 2009 | Kenmore 98702 Stacked Washer/Dryer

1 Answer

Repair manuel


If you are looking for an owner's manual for your washer, go to managemyhome.com and register. This is a FREE service. Once registered, log in and locate the "Products and manuals" link under the "Home" drop down menu. There are two manuals listed for your washer in down loadable .pdf format. I hope this helps you.

Sep 02, 2008 | Kenmore Washing Machines

Not finding what you are looking for?
Washing Machines Logo

Related Topics:

51 people viewed this question

Ask a Question

Usually answered in minutes!

Top Kenmore Washing Machines Experts

fordexpert

Level 3 Expert

5692 Answers

Harvey Mahal

Level 2 Expert

39 Answers

Kristen Denison
Kristen Denison

Level 1 Expert

13 Answers

Are you a Kenmore Washing Machine Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...