At Fixya.com, our trusted experts are meticulously vetted and possess extensive experience in their respective fields. Backed by a community of knowledgeable professionals, our platform ensures that the solutions provided are thoroughly researched and validated.
I had this problem for a while, then I couldn't get it to turn on unless I unplugged the unit. Now, that doesn't even work. I cannot get it out of standby mode. I had this problem for a while, then I couldn't get it to turn on unless I unplugged the unit. Now, that doesn't even work. I cannot get it out of standby mode.
I can turn it on, and it immediately shuts off. The standby button continues to flash. My troubleshooting page mentioned the Amplifier protection circuitry has been activated. How do you deactivate it?
I can turn it on, and it immediately shuts off. The standby button continues to flash. My troubleshooting page mentioned the Amplifier protection circuitry has been activated. How do you deactivate it?
You can't post conmments that contain an email address.
- If you need clarification, ask it in the comment box above.
- Better answers use proper spelling and grammar.
- Provide details, support with references or personal experience.
Tell us some more! Your answer needs to include more details to help people.You can't post answers that contain an email address.Please enter a valid email address.The email address entered is already associated to an account.Login to postPlease use English characters only.
Tip: The max point reward for answering a question is 15.
Hold the power button in for a few seconds it will shut down. Then unplug system and push the power button down with it unplugged then replug it in and power up again. Then do a proper shut down again to see if the problem fixed. I hope this assisted you. John
I had this problem also and discovered an easy way to trick it into powering on: Click the power button, then within 1 second of the receiver powering off, click the power button again. The receiver should stay on this time. This works with both the button on the receiver and the remote control.
I would like to know what causes this problem and whether or not I should be concerned about damage being done. I assume this is a power protection. I haven't tried plugging this receiver into a different power socket to test, but I don't think the power plug is the problem. Note: I have the subwoofer plugged into the power plug on the back of the receiver.
r this one: Switc off your receiver using the main power button on the
front face. Hold the the Effect button and the Direct button, and turn
the main power ON.f it ain't working, try this one: Turn your receiver ON and, while
holding down the [VCR1] button, press the [STANDBY/ON] button. "Clear"
might appears on the display and your receiver might enter Standby mode.
Hope it does.. With your receiver in the Standby mode, hold on STRAIGHT (EFFECT) on the front panel and press STANDBY/ON.
* The ADVANCED sETUP menu appears in the front panel display.ress STRAIGHT (EFFECT) to select the desired setting.
RESET = To reset your receiver to its factory presets.
CANCEL = To cancel without making any changes Press STANDBY/ON to confirm your selection.
* If you selected "RESET", your receiver is reset to its factory presets and switches to Standby mode good luck
hi im joe i have the same problem, but before this happened it turned the channel by its self and hade a mind of its own. to get it on unplug it. then as you plug it in repeatedly press the power button on the REMOTE. this will get it to turn on. if you get it on and some how get to control it then go into menu and put the fpd lock on. now you can only use the remote but at least it works. :)
I had this problem for a while, then I couldn't get it to turn on unless I unplugged the unit. Now, that doesn't even work. I cannot get it out of standby mode.
have unplugged and re-plugged in - turns on, immediately shuts off.
is there a reset button on the HTR500 ?
power will not stay on and goes stat to stad by mode
need solution
I can turn it on, and it immediately shuts off. The standby button continues to flash. My troubleshooting page mentioned the Amplifier protection circuitry has been activated. How do you deactivate it?
×