I have a Tork timer model number 1101 24 hr time switch. Can you tell me how to set it???

assuming that this is a mechanical timer with set points for off and on red points turn on and black points turn off. set the red point for your on time and then be sure to set black point for off. Best to tighten 1/8 turn (slightly) with pliers so it does not slip

Be frends

1) Copy following link to identify timer, and download possible manual:
http://waterheatertimer.org/Tork-timers-and-manuals.html

2) Tork TU universal
http://waterheatertimer.org/How-to-set-timers.html

3) Usually the dial will rotate manually until current time lines up with Time arrow located next to override lever, or time arrow located on inner dial, depending on model number.

4) Tork DTU digital timer:
http://waterheatertimer.org/How-to-wire-Tork-DTU40-timer.html

5) After opening links to identify timer, add comment and describe where you are, and what you discover.

If you need further help, I’m available over the phone at https://www.6ya.com/expert/gene_9f0ef4df2f9897e7

You can get the manual on the links below.

http://waterheatertimer.org/pdf/SS720A-Tork-In-wall-manual.pdf

http://waterheatertimer.org/Tork-consumer-timers-and-manuals.html

The Tork 602A mechanical outdoor timer with 2 grounded outlets.
Tork 601A and 602A manual
http://waterheatertimer.org/pdf/Tork-601A-Manual.pdf
Manual has images of timer that will help.

Plug timer into outdoor outlet.
To set current time, rotate dial clockwise until current time lines up with arrowhead located on inner dial.
Dial is divided into light and dark sections that represent day or nighttime hours.
Reset time after power outage.

96 pins located around timer dial are used to set on-off times.
Each pin represents 15 minutes in 24 hour day
Move pins in-or-out with fingernail or ink pen to set timer on-off functions.
With Tork timers, usually when pins are out, timer is ON.
When pins are in, timer is OFF.
To double-check pin setting, manually rotate timer to watch when lights turn on-off.

Set multiple ON/OFFs each day.
Change on-off times by resetting a pin or two.
Timer repeats every 24-hours.

Manual ON/TIMER switch is located on inner dial.

Set Manual switch to TIMER for programs to operate.
To override time and turn on Load, move override to ON position.

Tork 601A outdoor timer manual:
http://waterheatertimer.org/pdf/Tork-601A-Manual.pdf

Timer has 1 125Volt receptacle located on bottom of timer

96 captive tabs located around timer dial allow times to be set each 15 minutes.
Move pins in-or-out with fingernail or pen to set timer on-off functions.
Minimum time setting is 15 minutes.
Maximum time setting 23 ¾ hours.
Set multiple ON/OFFs each day.
Timer repeats every 24-hours.

Dial is divided into daylight and nighttime hours.
Nighttime PM hours are on dark background.
Daylight hours are on light background.

To set timer, rotate dial clockwise until current time lines up with arrowhead located on inner dial. Reset time after power outage.
Manual ON/TIMER switch located on inner dial.
To override time and turn on Load, move override to ON position. To use timer functions, move override to TIMER position

Tork, GE, Woods, Intermatic make a series of timers that have pins
The pins push out for OFF or ON times depending on brand

Tork makes a page-full of timers.

Rotate dial until current time lines up with arrow, then set the pins as shown in photo below

1) If timer plugs into wall receptacle, it has pins around the dial.
2) If timer replaced a wall switch it also has pins around dial.


GE and Woods and Tork and Intermatic each make similar timers.
Pull and push the pins to set times.
The wall-switch type timer also has a switch >>> move switch to Timer

Up-vote if this information helped. Thanks for the feedback.

Simple replacement for 120V 2-NO 2-NC is GE15207:
Selectable voltage
http://waterheatertimer.org/GE-timers-and-manuals.html#15207

Tork TU series also matches requirement:
Timer recognizes voltage
http://waterheatertimer.org/Tork-timers-and-manuals.html#TU