I am loosing green lights on my joystick quantam 600 power chair what could be wrong

The rippling lights on your Drive Seren mobility chair, followed by the chair stopping and the power sign coming on, could be indicating a problem with the battery or the motor. Here are a few steps you can take to troubleshoot the issue:

1. Check the battery connections: Make sure the battery connections are clean and tight. Loose or corroded connections can cause power issues.
2. Test the battery: Use a multimeter to test the battery voltage. If the voltage is low, try charging the battery. If the battery won't hold a charge or is more than two years old, it may need to be replaced.
3. Check the motor: Check the motor connections for looseness or corrosion. Test the motor by turning the chair on and listening for any unusual noises or vibrations. If the motor is malfunctioning, it may need to be replaced.
4. Check the joystick: Make sure the joystick is clean and free from obstructions. Test the joystick by moving it in all directions to see if it responds properly. If the joystick is faulty, it may need to be replaced.

If these troubleshooting steps do not resolve the issue, it may be necessary to contact a mobility equipment repair technician for further assistance.

This indicates the Joystick is bad.

I’m happy to assist further over the phone at https://www.6ya.com/expert/bill_bcbb89783b08c489

quantum 600 wheelchair troubleshooting Questions ... - Fixya

www.fixya.com > Forum > Tags

quantum 600 wheelchair troubleshooting chair won't go all i get form joystick is a picture of a ... around in a square there should be a rest button on the rear of the chair ,push ... Question about 600 E Electric Wheelchair - Used Power Chair.

[PDF]Pride Quantum 600 Owners's Manual - Scootaround

www.scootaround.com/.../Pride%20Quantum%20600%20Owner's%20M...

Quantum 600 .... The symbols below are used on the power chair to identify warnings, mandatory actions ... Pride will not be held responsible for injuries and/or property ...complete stop by releasing the joystick, then push the joystick forward slightly to .....breaker button, turn on the controller, and continue normal operation.

[PDF]Quantum 600E Owners Manual - Scootaround

www.scootaround.com/.../Pride%20Quantum%20600E%20Owner's%20...

Quantum 600E .... The symbols below are used on the power chair to identify warnings, mandatory ... chair. Pride will not be held responsible for injuries and/or property ... complete stop by releasing the joystick, then push the joystick forward slightly to ..... breaker button, turn on the controller, and continue normal operation.

[PDF]Quantum 600 Series - Pride Mobility Products

Have the joystick controller tested. Make sure the cable is fully seated in the chair connector.

Angel the charger light should only turn green when the chair is fully charged. If you know the chair isn't fully charged then there is a problem with the charging system. if the circuit board in the joystick got wet then that is a serious problem. If you have a voltmeter you can check the battery voltage thru the charging port located under the front of your joystick Set the meter to 200 volts dc and plug the leads into the 2 outter holes of the charger port. Fully charged you should read 27-30 volts if you aren't getting any reading then the batteries are completly dead or there is a problem with the charging circuit (the reason you are getting a green light on the charger) The joystick will have to be replaced sorry If Medicare paid for your chair then they will pay 80% of the repair costs to get your chair working again If they did contact Roadrunner Mobility @ 1-800-467-2668 to get it fixed thru Medicare Hope this helps

hi let me see if i can help ,

When the lights go back and forth on your joystick that means the chair knows its pluged in .Now the chair itself has a built in charger that is mounted on the back of your chair .The back of the chair ,there is a opening a cutout in the frame .when you plug in your chair there will be a red light and a yellow ,yellow means the chair is charging, wait till it turns green,this means fully charged.When you plug in the chair youll see the lights through that hole.Look for the lights.

I recommend my customers to leave there chair charging over night look at the light it will be green when you turn the chair on the joystick should show fully charge.


Good luck hope i was of some help.

The chair will not move if the charger is plugged in. The flashes are normal with the charger plugged into the chair. The lights on the charger mean that the batteries have been fully charged. Red and yellow lights mean charging. After you unplug the charger from the chair (if off-baord charger, turn charger off or unplug from the wall) then unplug from joystick. after plug is removed from joystick press the on button and all the battery lights should be lit and when you move the joystick forward you will hear the electric bake release and the chair should move forward etc Hope this helps

THE WHEELCHAIR WILL ONLY TILT IT WILL NOT GO FORWARD OR BACKWARD USING THE JOYSTICK

Unplug your joy stick and replug and retry it if that does not work call your dealer about it you may have a bad joystick