Kenmore model 119 24622300 Heavy duty 2 speed washing machine....The machine was in mid wash cycle and completely stopped. Although we have emptied the clothes and water out manually (it would not drain), the machine will not restart. It will fill with water but the agitator motor does not run anymore. It had a blanket in at the time it stopped running, so I dont know if there may be some kind of fuse that blew if the machine was overheating. I do know that the power cord and electric are still working properly. Is there a "reset" button anywhere on/in the machine that may have to be pressed? Thanks!!!!

belt mayb

Lid Switch Assembly

If the washer stops mid cycle the lid switch assembly might be defective. This is a very common problem. The lid switch assembly can fail either mechanically or electrically. Test any electrical switches with an Ohm meter for continuity. The switches should have continuity according to their design.


Enter your model number to see parts for your washing machine.
Help me find my model number

Door Lock Motor and Switch Assembly

If the washer stops mid cycle the door lock assembly should be checked. The door lock can fail either mechanically or electrically. Test any switches on the door lock with an Ohm meter. The switches should have continuity according to their design.


Enter your model number to see parts for your washing machine.
Help me find my model number

Water Inlet Valve

If the washer stops mid cycle the water inlet valve cold water side may have failed. Most washers have a cold water rinse and so if they can't fill with cold water they just sit indefinitely waiting for the cold water to enter. If there is cold water to the water inlet valve and the cold water works in other parts of the cycle - or to make warm water - the valve is not the problem.


Enter your model number to see parts for your washing machine.
Help me find my model number

Main Control Board

If the washer stops mid-cycle the main control board might be defective. This is not common. Check other causes first such as the lid or door switch and other components.


Enter your model number to see parts for your washing machine.
Help me find my model number

Timer

If the washer stops mid cycle the timer might be defective. This part is often misdiagnosed, check other components before replacing this timer.

God bless you

Yours is a 2 speed motor. Does it spin in 2 different speeds. If so, then it most likely is designed with only to agitate in 1 speed. If it only spins in one speed, then your motor is defective

My whirlpool heavy duty 2 speed 7 cycle washer machine stopped working, It fills up and aggitates for the first cycle then when it should drain and spin it doesnt drain nor spin

If the water drains between the wash and rinse cycles, your motor and pump are probably OK. If this is a machine with a dial, try a different cycle, like normal instead of heavy duty. If that works and the machine completes the entire cycle then the timer probably has a bad spot. You might try to find a replacement timer if that is the case although I didn't have any luck with my 10 year old washing machine. Best of luck

I would try a timer.
Sounds like there is a short in it.
Kenmore washer repair in orange county, ca
appliance repair orange county, ca

DOES IT DO THIS ON EVERY WASH OR SOMETIMES? IF SOMETIMES, CHECK LID SWITCH( THERE'S A LITTLE HOLE WHEN YOU OPEN THE LID, ON THE LID SHOULD HAVE A LITTLE PLASTIC PIECE THAT GOES IN THAT HOLE. THE SWITCH IS UNDER, INSIDE THAT HOLE. YOU CAN GET A PEN OR KEY TO SEE IF IT'S BROKEN.)
\
[email protected]

You may have a broken inner tub spider. Check for play between the inner drum and the outer tub by moving the inner drum up and down.
If there is excessive play, the spider is broken causing an unbalanced load and therefore no high speed spin can be achieved.

In this case the inner drum would need to be replaced, which means taking the machine almost completely apart. A good tech can do it in about 1.5 hours.

LID SWITCH read more HERE

If you need further help, reach me via phone at https://www.6ya.com/expert/dan_73bbd84fe1d95b61

You need a new SWITCH, LID 8318084 the bad lid switch is keeping your washer from sorking.. let me know if you want to repair it yourself.. let me know?