Mitsubishi WD65C9 dlp starts to turn for 2 seconds with green blinking light and shuts down immediately

How to replace the lamp in your Mitsubishi TV - YouTube

? 3:13


https://www.youtube.com/watch?v=_ONPuB5L-x4

Nov 1, 2012 - Uploaded by Mitsubishi3D

Your Mitsubishi television is powered in part by a 180 watt lampthat illuminates your TV's vivid colors. ... The first time they delivered my TV it was broken. ... I just barely got myreplacement bulb in today and it still only blinks orange light. .....I was watching my mitsubishi 73 3d model wd-73740 and ...

After replacing bulb on WD-82738 still not working - Fixya

www.fixya.com/.../t26028385-after_replacing_bulb_wd_82738_still_no...

6 mins ago - after replacing bulb on WD-82738 still not working bulb went out and burning smell. Replace the bulb, turned it in - Mitsubishi WD82738 82 ...

Mitsubishi WD-82738 Blinking Green Light - Tom's Guide

www.tomsguide.com/.../id.../mitsubishi-82738-blinking-green-light.html

Jan 12, 2015 - I have a Mitsubishi WD-82738 with the blinking green light of death as I have seen it called. ... Sounds like you replaced the parts, and it still is not working.... It would not work for us if we did it after the blinking. ... overnights. an ive already t akeing out the bat Forum; blinking green light changed bulb help!

Amazon.com: Mitsubishi WD-82738 DLP TV Asse

If you are getting at turn on source and back ground is all blue the set will shut down rather quickly;

I have a suggestion, if it works fine, and if not it will not hurt anything.

with original Mitsubishi remote turn set on and then Menu, 1,2,3, enter.

This is the soft reset that most of these sets have (cannot be sure since Model number above is correct?)

The reset button on the front (if it has it) just shuts the set down and reboots the DM unit inside.

Most of these sets when it is pressed the green light will blink for about 70 seconds and go out; that is the DM unit rebooting and the soft restart is something else.

Let me know what you find before you rate this information.

SD TECH

Mitsubishi self check: MOST OF THESE SETS HAVE A SELF DIAGNOSTIC:

UNPLUG TV AND THEN PLUG BACK IN---TURN ON---GREEN POWER LIGHT COMES ONFOR A MOMENT AND GOES OFF.

PRESS AND HOLD "device" and "menu"buttons on front of tv for at least 5 seconds and then release both together.


Watch for power light to blink in a sequence:

1 blink-then 2 blinks-------no error

2 blink-then 1 blink-------X-ray protection

2 blink-then 2 blink-------SHORT PROTECTION*******

2 blink-then 3 blink---------deflection circuit problem

2 blink-then 4 blink---------vertical circuit problem


******2, then 2 is most common---usually means one of the fuses that protectthe Convergence IC or IC's is blown---set will detect no voltage to convergenceIC and shut down.


SET WILL REPEAT BLINK ERROR CODE UP TO 5 TIMES ANDTHEN TO GET IT TO REPEAT MORE YOUHAVE TO UNPLUG SET AND TRY TO TURN ON AGAIN.


IF IT IS 2 AND THEN 2---USUALLY
CONVERGENCE CIRCUIT PROBLEM

let me know what you find--hope that you find 2 blinks, a pause and twoblinks--this is the most common and easiest to fix.

Only get Welcome screen and green blinking lite. Then shuts off. Buttons locked out also. Need to get software update V41C-11.3 Mitsubishi-tv.com. Go to support then software update. It will ask for model, ser. First and Last name and E-mail. download. http://www.avsforum.com/avs-vb/showthread.php?p=19844230
Has a link about 1/3 way down that will go right to the download. Very helpful.

Hello Sir, hi, you have power supply problems, this is caused by a bad part on the main board or on the power supply board to overload, when overload happens, the power supply immediately shuts down to prevent further damage. my first advice is call your dealer for proper service.

Do the self check it should have: when shuts down and green light goes out: On the front of the set press and hold both input and menu buttons at the same time for at least 5 seconds and then release both.

Power light on set should blink a two digit error code: like 2 blink,2 blink, pause and repeat it at least 5 times total.


Let me know what error code and I will tell you what it means.


If this has helped you, rate this solution as I do this here for free.



SD TECH

Normal 0 false false false MicrosoftInternetExplorer4 /* Style Definitions */ table.MsoNormalTable {mso-style-name:"Table Normal"; mso-tstyle-rowband-size:0; mso-tstyle-colband-size:0; mso-style-noshow:yes; mso-style-parent:""; mso-padding-alt:0in 5.4pt 0in 5.4pt; mso-para-margin:0in; mso-para-margin-bottom:.0001pt; mso-pagination:widow-orphan; font-size:10.0pt; font-family:"Times New Roman"; mso-ansi-language:#0400; mso-fareast-language:#0400; mso-bidi-language:#0400;} MOST OF THESE SETS HAVE A SELF DIAGNOSTIC:


UNPLUG TV AND THEN PLUG BACK IN---TURN ON---GREEN POWER LIGHT COMES ON FOR A MOMENT AND GOES OFF.

PRESS AND HOLD “device”(or input) and “menu” buttons on front of tv for at least 5 seconds and then release both together.


Watch for power light to blink in a sequence:

1 blink-then 2 blinks-------no error

2 blink-then 1 blink-------X-ray protection

2 blink-then 2 blink-------SHORT PROTECTION*******

2 blink-then 3 blink---------deflection circuit problem

2 blink-then 4 blink---------vertical circuit problem


******2, then 2 is most common---usually means one of the fuses that protect the Convergence IC or IC’s is blown---set will detect no voltage to convergence IC and shut down.


SET WILL REPEAT BLINK ERROR CODE UP TO 5 TIMES AND THEN TO GET IT TO REPEAT MORE YOU HAVE TO UNPLUG SET AND TRY TO TURN ON AGAIN.


IF IT IS 2 AND THEN 2---USUALLY
CONVERGENCE CIRCUIT PROBLEM

if this information has helped you rate this solution as I do this here for free.

SD TECH

set has a self diagnostic---after set does shut down press and hold MENU AND DEVICE(INPUT) buttons on front of set for 5 seconds----if 2 blinks, a pause and 2 more blinks: this is short protection error code---The set does use 2 Stk394-250 and each is protected by a pico fuse in the power supply---if either fuse is blown the set will shut down(it detects no voltage or missing voltage;) It is not uncommon for a shorted IC to cause this problem; if you locate the STK's look carefully at the resistors around them---if any are discolored or burnt---you have found your problem.

There are (4) 1000uf @35V capacitors all together on the DM board that need to be replaced some models have 1000uf @ 16V but they are all right beside each other and all rated at 1000ufs the voltages will be stamped on the capacitor along with the uf ratings.