Is there a volume adjustment for hand set on KX-T7640

Do you mean the Panasonic KX-TGA470 handset? The KX-TGA470 handset is the included handset for several models of Panasonic cordless phone systems, including the KX-TG7732. When the ringer is off, the handset should show a bell with a line through it. To adjust the ring volume, press Menu on that handset when the phone is in standby. (The base and handsets are not in use.) After pressing the Menu button, type # 1 6 0. (Alternatively, use the arrow keys to navigate to Initial Settings and press the soft key for Select. Navigate to Ringer Settings and press Select again. Go to Ringer Volume Handset and press Select once more.) Use the arrow keys to select a value between 0 and 7. 0 will keep the ringer disabled. Press the soft key for Save. Press Off to exit the menu.

You can also adjust the ringer volume on that handset by pressing the Volume Up key while the phone is ringing at the base and other handsets. You can adjust the base ringer volume by pressing the + or - keys when the phone is ringing. Alternatively, press Menu # * 1 6 0 from any handset. Note: this phone system also has a silent mode. Press Menu # 2 3 8 to enable or disable the feature. When this is enabled, the handset will show an icon with several Z's.

You can find the manual on the phone system page: https://shop.panasonic.com/support-only/KX-TG7732S.html . The current link to the manual is ftp://ftp.panasonic.com/telephone/om/kx-tg7731_mul_om.pdf . See pages 23 and 35 for the ringer volume adjustment. See pages 35 and 40 for information on the silent mode.

I hope this helps.

Cindy Wells

KX-TGA402C is the included handset for a Panasonic cordless phone system like the KX-TG4011C. You should be able to adjust the ringer volume from the Initial Settings menu. With the phone system in standby, press Menu on one handset. Use the Up/Down arrows to locate the Initial Settings. Press OK. Then select Ringer settings and press OK. Select Ringer Volume and press OK. Use the Up/Down arrows to set the desired Ringer volume and press OK to save. Press Exit to leave the menu system. Alternatively, you can adjust the ringer volume by pressing the Volume Up/Down buttons while the phone is ringing.

The manual for the KX-TG4011 is available from Panasonic here: ftp://ftp.panasonic.com/telephone/om/kx-tg4011_mul_om.pdf . If the above steps aren't working, check that your handset and phone base are properly paired (registered handset). Also check that the base has power and connected to a working phone line. Also make sure that the handset is fully charged.

I hope this helps.

Cindy Wells

Temporary ringer off While the handset is ringing for an outside call, you can turn the ringer off temporarily by pressing {OFF}.Adjusting the base unit ringer volume Press {^} or {V} repeatedly to select the desired volume.To turn the ringer off, press and hold {v} until the unit beeps 2 times

Press the volume up. If you're on speakerphone it adjust the volume of the speaker. If you are on your handset it adjusts that volume.

Hello

The handset navigator key can be used

to navigate through menus and to select
items shown on the display by pressing (UP) (DOWN) (REVERSE) (FORWARD) buttons on the handset.
Adjusting audio volume

Press UP or DOWN button repeatedly while
talking.
The last settings of volume level will be memorized when you switch OFF the habdset. OK.

on the bottom right hand corner of your phone, rotate the dial clockwise to increase volume, or counter clockwise to decrease(must be done DURING a call)

With Panasonic phones the volume of whatever function is active can be adjusted with the arrows button. While it is ringing use the arrow up or down to adjust ringing volume. When off hook (you can hear dial tone or you are on a call) use arrows to adjust handset volume.

Lift the handset, whereon the word 'handset' will display on the console. At that point you can use the up or down arrow on the round raised console key-pad to turn the volume louder or softer.

A 7640 has on display, so it's going to be a tough assignment. I'm guessing it sits next to a 7636 and that DOES have a display.

If it's extension 101 or programming is allowed from that set, press PROG, dial **1234 and ENTER then ENTER (note it changes soft key positions)

You should be looking at program 000 which is the date and time.
The FWD button steps the display forward and the ENTER will save the new time when you're completely done, then, I think you get an EXIT key, or pick up the handset and set it back down to exit.

Carl

I'm looking for a user manual of a KX-T7640 phone, but it doesn't seem to exist. Who can help me?