The enp-2320 will not turn on, any thing i can do? is there a fuse i can replace?

The following is based on the assumption that the Imagerunner 2320 is already connected your network. If it isn't, that's the first thing that needs to be done.

It's your computer that needs to be configured. Follow the instructions on page 55 of the User's Manual,

Before Using the Remote Scan Function

https://www.manualslib.com/manual/639767/Canon-Imagerunner-2320.html?page=55#manual
You may have to go the Canon website to download the Imagerunner scan driver software for your computer.

When you have that set up, then go to page 76 of the manual ("Basic Remote Scanning) for instructions on scanning operations.

Basic Remote Scanning

https://www.manualslib.com/manual/639767/Canon-Imagerunner-2320.html?page=76#manual

Dear Its related to fusser temp. Check the fusser assy. thermostat it may open . either it may reset or replaced with new one. The error code mean-OPEN HEAT ERROR.
thanks

search thru youtube.com

DC OUTPUT LOW VOLTEG

It is the green wire in general you must plug a wire between Greens a black wire to put the power on
It called "remote on/off" because on old AT the power wasn't plugged on by the motherboard but by a switch directly wired in the PSU

Do not try to fix this power supply. Better to replace with new or good used. I see many on ebay from 13.50 to 25.00. Also google that model for other options. Most likely fuse on the power supply has failed but if you bypass the fuse, with jumper wire or another fuse, will blow again. Probably capacitors. Good luck

The only thing to do at this point is to replace the Power Supply with a KNOWN to be good, compatible unit, and see if the rest of the computer hardware components are okay.

Going by your information stated that the Power Supply is an Enhance ENP-2224B SMPS, (Switched-Mode Power Supply), it is a special shape.

If it wasn't for the Slim Micro-ATX computer case you have, you could use an easy to obtain ATX form factor Power Supply.

From a quick search though it looks like a replacement unit is affordable,

http://www.censuspc.com/Enhance-ENP-2224B-2G-240W-SATA-TFX12V-P4-Power-Supply-for-Slim-microATX-Desktop-Case-Serial-ATA-Ready-bulk-pack-SKU-ENP-2224B-2G-pr-3033.html

There is simply no way to tell if the motherboard, and/or Processor, and/or Ram Memory, and/or Harddrive, etc., is okay without having power.
Unless you transfer the components on the motherboard to another working motherboard.

[NOTE*
If your Power Supply has a rocker switch on the back that lets you use 120 volts, or 220 volts, make SURE it is set to the right voltage.

USA?
120 Volts
Europe?
220 Volts
Australia?
220 Volts
Japan?
100 Volts ]

For additional questions please post in a Comment.
Regards,
joecoolvette

http://www.shopwiki.com/Shuttle-XPC-SN41G-power-supply

http://www.google.com/#q=Enhance+200W+TFX12V&hl=en&prmd=ivns&source=univ&tbs=shop:1&tbo=u&sa=X&ei=fp6GTf6NAo7sOfKZ0eoI&sqi=2&ved=0CDUQrQQ&biw=1004&bih=583&bav=on.2,or.r_gc.r_pw.&fp=52f01a95353e1206
This is a google search which produced many hits. Mostly 49 dollars, one 'refurbished' for 17.10ish
Just click on this link to bring up same list.

that is problem of ram replace the ram problem will be solved