Have LE1HDC110SC cooker hood. Has been damaged and the edging surrounding the canopy has been dented. Can this part be replaced?

It depends a lot on the area the dent is in, the size and if the paint is cracked, damaged or scraped off. If the dent is on a body line, its going to take a lot more to fix it, if its in an open flat area without any sharp creases, you can many times do some paintless dent repair and bend it back into shape. This is the least expensive method.

If its a fender that can be removed, many shops now get a replacement fender and paint it to match. When you match paint, you generally need to blend the surrounding fenders/hood/body to get it to look right. There is a lot of skill involved with paint matching and the application of paint. Unless you have a shop and the equipment to spray it, you would need to get someone with experience to apply the paint so it looks right.

The 3rd option to repair the dent is to get a body hammer set, with a dolly/flat hammer etc and pound the dent as close to its original position as possible, then use a body filler and sand it. This part could save you money if you want to choose and have someone paint it. Or if its an old car, you could have the paint matched with the car and put in an aerosol can where you could spray it on yourself. Its not going to be perfect by a long shot, but certainly better than a big ugly dent thats been repaired and primered

EN Control buttons separating from control mounting bracket. Affected Countries CA, US Affected Appliances HPCN36NS/01, HPCB36NS/01, HPCN48NS/01, HPCB48NS/01 Fault description / Customers complaint / Diagnostic Codes Diagnostic Codes (DC) The following table contains the diagnostic codes, which most commonly occur in connection with the mentioned fault description. Depending on the actual information from the customer, other diagnostic codes are possible. DC Fault description of the customer 160100X45000 Mechanical damage / Holder Root cause On some Thermador Professional hoods with FD 9407 to 9611, the control buttons may separate from the control mounting bracket due to insufficient adhesive between the control mounting bracket and the inside of the hood canopy. Solution Beginning with FD 9612, wider tape was implemented in production. For units built prior to that time, service kit 12022532 is available. The new repair kit includes the control-mounting bracket with wider tape affixed to it, and four screws. The tape will provide more surface coverage to improve the support of the mounting bracket.

It it new? Maybe the fan connection in the connection panel come loose or was not done properly from factory. Turn off the breaker to the hood and inspect the wires and connections, if all is good, then maybe the switch needs replacing. Good Luck!

it would be hard to estimate a dent without seeing it because not only the damage parts but the actual dent in the frame or structure has to be evaluated if you can provide pictures will be a lot easy

Common problem. Have someone pull the release while you bang on the edge of the front of the hood with the heal of your hand, keep on the edge as you can dent the hood very easy. it will pop open then spray the latch with WD40. Let me know if this works.

Try this. have some one pull the release while you bang on the front edge of the hood, be careful as the metal on the hood is thin and will dent easly. Try to use the heel of your hand right on the edge of the hood in the middle front edge against the bumper. The hood should pop up. When it is open sprayWD40 all over the lock and latch. Let me know if this works.

Hi
www.buggypitstop.co.uk/

Hi,

I would recommend either eBay or www.quinny.com

Hope this helps.

Hello,

Here are the dimensions that relate to your cooker hood. The measurements are in mm.

Width 980 front 578 rear
Depth 480
Minimum height 1015
Maximum height 1170
Main canopy height 750
(excl chimney)
Chimney section width 436 main body/340 sliding section
Chimney section depth 170
Mounting height 650 - 750

Regards
Alan Hood
ami-man
Width 960 front, 578 rear Depth 480 Minimum height 1015 Maximum height 1170 Main canopy height (excl. chimney) 750 Chimney section width 436 main body / 340 sliding section Chimney section depth 170 Mounting height 650 - 750
Width 960 front, 578 rear Depth 480 Minimum height 1015 Maximum height 1170 Main canopy height (excl. chimney) 750 Chimney section width 436 main body / 340 sliding section Chimney section depth 170 Mounting height 650 - 750 Width 960 front, 578 rear Depth 480 Minimum height 1015 Maximum height 1170 Main canopy height (excl. chimney) 750 Chimney section width 436 main body / 340 sliding section Chimney section depth 170 Mounting height 650 - 750 Width 960 front, 578 rear Depth 480 Minimum height 1015 Maximum height 1170 Main canopy height (excl. chimney) 750 Chimney section width 436 main body / 340 sliding section Chimney section depth 170 Mounting height 650 - 750