Simply will not turn on..it clicks but does not go on

most simply snap on. i sit with elderly and have to clean these all the time. the small pieces inside come apart, but you simply put the round pieces back in first, thenthere should be a bigger piece to fit over all three small round pieces. simply line it up over the 3 round pieces, and turn slightly clockwise and it should click. once that is in place, simply take the two hinged looking pieces and push into the device where they line up, and it should just snap in place.

The socket the bulb plugs into must be turned to the right (as if it is reverse threaded), then the bulb and socket will release. The bulb itself is simply plugged straight in, so simply pulling straight on it should remove it from the socket. Then, press the new bulb (#4157NA) firmly into the socket until you feel it "click" in, and reinsert the bulb/socket assembly back into its housing and turn it to the left until the socket "clicks" to lock it back in place.

Hi this "Clicking" is the sound of a Switch Mode Power Supply problem, what has happened is that a component either IN the PSU or the unit's electronics has, or will fail in such a way that it may cause a fire and explosion or both, accordingly the protection mechanism is kicking in and attempting, has? to shut the set down.
The failure maybe almost anything from any section from the PSU itself to any of the "Other" electronics boards etc, one simply must use the troubleshooting steps to isolate and identify the problem and repair that and any damage done by the failure. There is no simple fix or route.
DIY in reality is NOT an option, and most often, in my experience, simply ends up with a large parts bill, lots of headaches and hassles, and still no repair. Also one simply must obtain service manual, if only for the parts numbers, this too may cost.However if you wish to explore this you will need to Google search for the manual using the exact make and model.
The very best thing you can do is to contact a local or head office from Samsung, and ask them for a referral to an authorised service center, now make contact there, and then when in face to face contact only ask for a "Quote" as to prospective costings and go from there as to repair or replace.

It is most likely popping up because it's recommending that you do a backup, if you use the program but simply don't want it to constantly be popping up, you should be able to find the program in the list of programs in your start menu, and from there there should be an option to turn off reminders/notifications.
If you do not use the program and simply want to get rid of it, if you click start, control panel, then 'programs and features' or 'add/remove programs' depending on your version of windows, you should find a list of all the programs installed on your computer, simply find the backup program and click uninstall.
hope this was helpful.

Hello, I think you must need to make use of the DirectX Diagnostics and then you can simply turn on your DirectX if it is turned off. For that you need to follow the steps below:

• Click on the Start.
• Then click on the Run.
• Then type the command as "dxdiag" without quotes and press enter.
• When then progress bar disappears click on the Display tab.
• Then simply enable the DirectDraw, Direct3D and AGP texturing.
• Done.

Hello there!

Simply click on start>hover on the shutdown button and a menu will appear on the right side then click on restart. This is known as a warm boot.

To do it manually, simply hold on the power button until it turns off, wait for about 10 seconds and then re press the power button. This is known as a cold boot.

Please rate and comment, thank you.

On some laptops the switch used to disable WiFi also disables bluetooth. If that's not the case for you, you can turn bluetooth off by simply right clicking on the bluetooth icon in the System Tray (next to the clock on the Start bar) and clicking "Turn Adapter Off"

Log in to your modem using 192.168.100.1
You will see a configuration button on the left, click that.
Click the factory reset / restore default settings button.
To simply turn i toff and on click reset cable modem below or simply unplug and replug the power cord.

The proper way to shut down a computer is to click on START - Turn off Computer - then click Turn Off.