Kenmore 700 series dryer doesn't seem to dry as quickly as it used to. Just want to clean it good but am not sure how to do that. Any guidance available on how to do a thorough cleaning on this dryer?

To reverse the door on a Kenmore 700 series dryer, you can follow these general steps:

1. Gather the necessary tools: You may need a Phillips head screwdriver, a putty knife, and a small flathead screwdriver.
2. Unplug the dryer: Before starting any work, ensure the dryer is unplugged from the power source for safety.
3. Remove the hinge cover: Use a putty knife or a small flathead screwdriver to carefully pry off the hinge cover located on the opposite side of the door.
4. Remove the door: Locate the screws that secure the door to the dryer and use a Phillips head screwdriver to remove them. Carefully lift the door off the hinges and set it aside.
5. Remove the strike plate: On the opposite side of the door opening, remove the strike plate by unscrewing it.
6. Remove the door hinge: Unscrew the door hinge from the side it is currently attached to and transfer it to the other side of the opening.
7. Install the strike plate: Attach the strike plate to the opposite side of the door opening using the provided screws.
8. Reinstall the door: Place the door onto the new hinges and align it properly. Insert and tighten the screws to secure the door to the dryer.
9. Reinstall the hinge cover: Snap the hinge cover into place on the side where the door hinge used to be.
10. Test the door: Close and open the door to ensure it operates smoothly and securely.

It's important to note that specific instructions may vary depending on the exact model and design of your Kenmore 700 series dryer. Therefore, it is recommended to refer to the user manual or installation instructions provided by the manufacturer for detailed and model-specific guidance on reversing the door.

AF stands for Algorithm Failure, which means that there is something preventing the dryer from calculating the remaining time. Try cleaning out the dryer drum and lint screen completely, then run the dryer with just a dry towel.

change out the lid switch

replace the coil valve which is on the gas burner assembly it should be a $10 part and is easy to replace

check your vent 99% of all dryer problems are caused by the vent, Make sure you do not have too many turns in the vent hose and ithe lenght is as short as possible

Hi,

If your dryer is not drying like it once did or if you just have not taken the time to give yourself a clean dryer in a long time then you need to do that. At least once a year the dryer cleaning should take place. Lint build up in the dryer duct is one of the main causes for your dryer to fail.

Here is the rest of this tip about Dryer Maintenance

heatman101

The Kenmore 80 Series of dryers are consumer grade dryers for home use. As with most home appliances, the Kenmore 80 series dryers will occasionally not work as intended. If a problem occurs with your dryer, however, you do not necessarily need it serviced by a technician. You can attempt to troubleshoot and fix any problems with your dryer before contacting a technician.

1. Kenmore 80 Series dryers may not run for several reasons. First, make sure that the power cord is plugged into a working power outlet. You may need to plug a different device into the outlet to check that it is receiving power. If the second device does not run on the power outlet, you may have blown a fuse or tripped a circuit breaker. Check your fuse box or circuit breaker box and make the change as needed.
   Next, make sure that the dryer door is fully shut. The dryer will not run with the door ajar.
   Finally, check that the "Start" button was fully pressed and that a cycle was chosen on the machine. If you do not choose a cycle for the dryer, it will not run.
2. If your Kenmore 80 Series dryer does not heat up during use, check that a heat cycle has been chosen for the load. There are several different dryer cycles you can choose, some of which do not use heat. Make sure that you have chosen a heated cycle.
   As above, check that you have not blown a fuse or tripped a circuit breaker. The dryer may use more than one fuse or breaker: one is used to power the drum, and the other for the heating element. Make sure that both fuses or breakers are in working order.
3. There may be times when Kenmore Series 80 dryers do not fully dry your clothes. When this occurs, check the lint screen and clear out any lint. The air may not flow as well if the lint screen is clogged.
   Next, check to see if the exhaust vent is clogged. Lint and other particles may clog the exhaust vent over time, restricting air flow and making it more difficult to dry your clothes. To check the vent, run the dryer and hold your hand under the vent. If you do not feel any air flow, clean or replace the vent.
   If you used cold water to rinse the clothes it may take longer than normal to dry. The same is true if the load of laundry is very wet or is filled with items that are very absorbent.
   Finally, check the load size. The more clothes in the load the longer it will take to dry. If you want to reduce drying time, separate the clothes into piles of light and heavy items and dry them separately.
4. please comment on these solution by saying how helpful.
   

This is usually the dryer coils have failed. They tend to fail as they heat up. They are inexpensive and easy to replace. Here is a video on replacing the dryer coils.

Very common problem. You need to call a
duct cleaning company and tell them to clean
your dryer vent. Rule-of-thumb: dryer vents
should be cleaned every couple of years to
prevent them from being clogged with lint and
causing lint fires. This is definitely your problem. Good luck :)

p.s. one way to verify a clogged vent is
to go outside where the vent exits the house
and feel the air-flow. should have adequate air-flow.