Green light flashing 4 times,sencors lights on,press & hold wall button to open.others wont work

Question 1

0helpful

1answer

Merlin Prolift 230T wont clear / delete remotes from memory

Press 'setup' key for 11s not 'learn' key.

Jun 26, 2012 • Cell Phones

tip

How to Reset Your Water Filter Light

Amana: <ol> <li>Press and hold the dispenser lock and auto light buttons on the dispenser for 4 seconds until the filter status indicator begins to flash, then release the buttons.</li></ol>or <ol> <li>Press and hold the dispenser lock and water buttons for 4 seconds until the filter status indicator begins to flash, then release the buttons.</li></ol>or <ol> <li>After replacing the water filter, press and hold the Reset Filter pad for 3 seconds. The Order and Replace indicator lights will blink and then go off when the system is reset.</li></ol>Brita: <ol> <li>Press firmly and hold start button for 5 to 10 seconds.</li> <li>Four bars will appear in the display, one after the other, and flash. Do not release the start button until the 4 bars appear and start to flash. If you have difficulty pressing the start button, a capped ballpoint pen may be used to press the button down.</li> <li>A small flashing dot in the lower right corner shows the indicator is working.</li> <li>Every 2 weeks a bar automatically disappears. When only 1 bar remains make sure you have a new filter on hand.</li> <li>After 2 months, when all bars have disappeared, an arrow will flash at the top of the display reminding you to change your filter. </li></ol>Frigidaire <ol> <li>Press and hold the reset button on the dispenser until the green light flashes (up to 15 seconds).</li></ol>GE: <ol> <li>Press and hold the reset water filter button on the dispenser for 3 seconds.</li></ol>or <ol> <li> Press the reset button on the dispenser for 4 to 8 seconds then release. </li></ol>Hotpoint: <ol> <li>Press and hold the reset water filter button on the dispenser for 3 seconds.</li></ol> Jenn-Air: <ol> <li>Press and hold the lock and light buttons (lock and water on newer fridges) on the dispenser for about 4 seconds, until the indicator light blinks.</li></ol>Kenmore: <ol> <li>Press and hold the button next to the filter light for 10 seconds.</li></ol>KitchenAide: <ol> <li>Press the light switch 5 times within 10 seconds. If the fridge has a filter button, press and hold it for 5-10 seconds.</li></ol>LG: <ol> <li>Press and hold the reset button for 3 seconds.</li></ol>Magic Chef <ol> <li> Press and hold the light and lock pads until the change filter light flashes. (approximately 3 seconds)</li></ol> Maytag: <ol> <li>Press and hold the lock and light buttons (lock and water on newer fridges) on the dispenser for about 4 seconds, until the indicator light blinks.</li></ol>or <ol> <li>Press the refrigerator's light switch five times within ten seconds.</li></ol>Samsung: <ol> <li>Press the ice type and child lock buttons simultaneously for 3 seconds. NOTE: Hold the buttons for only 3 seconds. If you press these 2 buttons simultaneously for 5 seconds, the reset function ceases.</li> <li>Release the buttons and repeat the same step one more time. The water filter indicator light should turn green.</li></ol>or <ol> <li>Press and hold the "Alarm/Hold" button for 3 seconds.</li></ol>or <ol> <li>Press and hold the Fridge and Power Cool buttons for 3 seconds.</li></ol>Whirlpool: <ol> <li>Press the light switch 5 times within 10 seconds. If the fridge has a filter button, press and hold it for 5-10 seconds.</li></ol>

on Jun 17, 2011 • Refrigerators

0helpful

1answer

Error code 5100 check printer

This is probably a Canon printer and code. If so, it is the "ink waste pad is full" warning. There are work arounds to keep from having to clean the pad. Here are two methods to eliminate the message. The only other ways are to take it to a repair shop or dismantle the printer and clean the pad yourself. Not advised, This is messy.

This works on many different printers.

Waste ink full reset

These are the instructions which worked for me on my Canon pixma mp470:

1) Close the print head cover, and turn off the printer. While pressing the Resume/Cancel button, press the Power button. (Do not release the buttons. The LED lights in green to indicate that a function is selectable.)

2) While holding the Power button, release the Resume/Cancel button. (Do not release the Power button.)

3) While holding the Power button, press the Resume/Cancel button three times, and then release the Power and Resume/Cancel buttons. (Each time the Resume/Cancel button is pressed, the LED lights alternately in either orange or green, starting with orange.) During initialization, the LED blinks in green.

4) When the LED stops blinking and lights in green, press the Resume/Cancel button the 4 times. (Each time the Resume/Cancel button is pressed, the LED lights alternately in either orange or green, starting with orange.)

5) Press the Power button. The LED lights in green, and the
selected function is performed. (When the operation completes, the printer returns to the menu selection mode automatically.)

6) Power off then back on and test.

mp150 and simular printers:

printer powered off but connected on power source , you must:
1. Press & hold stop/reset button, and then press & hold [ON/OFF] button.
2. When Green power lit, leave stop/reset button & press twice stop/reset (see orange indicator).
3. Leave On/Off button. Printer in actually service mode.
4. Press stop/reset 4 times (see orange indicator) if not blink restart above process from top.
5. After press stop/reset 4 times successful press On/Off button 3 times. printer will off.
6. Press On/Off button.

Jan 22, 2011 • Office Equipment & Supplies

26helpful

3answers

Ink absorber full, ip2600

I have a ip2600 that has had the waste ink absorber msg come up twice. After trying several recommended fixes involving pressing the Resume key twice then 4 times, etc., I've found the perfect solution. Start by cleaning the waste pads with tweezers, etc.
1. Press Power Off
2. Disconnect Power Cord
3. At SAME TIME, Press & HOLD Power Key while re-connecting Power cord
4. Release the Power button
5. Press the power button again
This will work!

Nov 18, 2010 • Canon Pixma iP2600 Photo InkJet Printer

0helpful

1answer

Xbox 360 power button light keeps flashing and disc tray does not open

Hi when the power button flashes red if you hold down the little round white button under the dvd tray and keep holding it down then press the open button for dvd then it will flash a number of lights write this down.
it will be flashing 1 2 3 or 4 lights so write it down then hold down the white button again and press the draw open button again and write down how many again.
do this 4 times all together and tell me what code it has given you then i can tell you exactly what the problem is

so for instance
you hold down the little white wireless button and keep holding it down then press the open button for the dvd tray and say 4 lights are flashin
so write down 4
then hold white button down again and press open button again
it may flash 4 again
then do it again and it may flash 2 lights
then again and it may flash 2 again

when you have gotten these 4 codes post me a message and tell me exactly what they tell you and in the correct order so it may look like this
4 lights flashing
2 lights flashing
1 light flashing
2 lights flashing

if you look at where the button is where you turn it on well you have the green light in the middle well around this is four outer lights that light up red their are 4 of these 2 at the top and 2 at the bottom either side of the green light, their the ones that flash green when its spinning rounf with green lights so write this code down then ill be able to tell you exactly what the fault is ok

let me know then i can assist you further ok

Oct 05, 2010 • Microsoft Xbox 360 Console

1helpful

1answer

Just wall switch works transmitters won't light

You probably have the opener lock turned on. Press and hold the lock button on the wall button pad for four seconds. The green light will go solid instaed of flashing

Jun 14, 2010 • liftmaster Chamberlain Garage Door Opener...

3helpful

2answers

My garage door wont go down.I habe to hold the switch down but if i let it go the door will go up again.

I have a Liftmaster garage door that won't go down unless you press and hold the wall button. The sensor lights are both on. The green light on the unit flashes unless I press the reset button. As soon as you press the wall button it flashes again and the door won't go down unless you hold the button the whole time. The remote wont' make it go down either. It begins to sometimes and retracts, but sometimes the light bulb just flashes (like it is obstructed). I tried replacing the wall switch and that did nothing. Help!

May 16, 2009 • Sears Craftsman LiftMaster Chamberlain...

2helpful

2answers

Garage Door Wont Close Craftsman 1/2 HP (1998)

What it is is the electric beams at the door are getting blinded buy the sun or out of line. They are the two black boxes on both sides of the door about a foot from the ground. Put a piece of card board in front of them not blocking the beam dut to block the sun. All that they are is safety beams for kids so they do not get hurt. If you have to move them to the top where the sun will not hit them. Sorry to say though you can not remove them all the way. Also make sure the lite on them is not blinking if so they are out of line.

Good Luck and Please Rate FixYa!

Mar 03, 2009 • Sears Craftsman LiftMaster Chamberlain...

0helpful

1answer

S9000 canon printer ink tank full

Hi
Try this see if work for you.
may work
Canon S9000, S300, S400, i550, i560, i850, i860, i865, i9100, i9950, PIXMA iP3000 above,
1. Turn off printer
2. Hold down Resume button and press Power button.
3. Keep holding down Power button and let Resume button go.
4. Press Resume button 2 times then let BOTH buttons go.
5. Green lights will flash and then stop blinking.
6. When green lights are solid, press the Resume button 4 times.
7. Press the Power button and the printer should turn off, if not, press the Power button once more.
8. Your printer should respond as normal.

Nov 02, 2008 • Canon i950 InkJet Photo Printer

0helpful

1answer

The remote opener reset button goes off and will not work

The green button is not a reset it is the program button.

If you hold the button down for about 20 seconds it will erase all codes. Then, press and release the button - press and hold the button on your remote for about 10 seconds. the next time you press it it should activate the door. Repeat the 2nd step for all additional remotes.

The lock button on the wall control locks out all radio signals for vacations etc.

If the lock has been activated the green led in the wall control will flash - when the lock is deactivated the led stays solid green.

Hope this helps

May 07, 2008 • Sears Craftsman LiftMaster Chamberlain...

Question 2

Anonymous

Master 3,197 Answers
Posted on Aug 23, 2010

Anonymous

Master

Joined: Apr 29, 2009

Answers

3197

Questions

1

Helped

1458694

Points

8183

The green light flashing 4 times is sending the code for " Safety reversing sensorsslightly misaligned (dim or flashing LED)". These are the sensors in the doorway. Tweak them a bit.

Related Topics:

Trustworthy Expert Solutions

Green light flashing 4 times,sencors lights on,press & hold wall button to open.others wont work

1 Answer

Anonymous

Add Your Answer

Attachments: Added items

Related Questions:

Merlin Prolift 230T wont clear / delete remotes from memory

How to Reset Your Water Filter Light

Error code 5100 check printer

Ink absorber full, ip2600

Xbox 360 power button light keeps flashing and disc tray does not open

Just wall switch works transmitters won't light

My garage door wont go down.I habe to hold the switch down but if i let it go the door will go up again.

Garage Door Wont Close Craftsman 1/2 HP (1998)

S9000 canon printer ink tank full

The remote opener reset button goes off and will not work

Not finding what you are looking for?

Craftsman LiftMaster Chamberlain Garage Door Opener Wireless Keypad Model 976LM Security+

Merlin Prolift 230T wont clear / delete remotes from memory

Ask a Question

Top Sears Building Materials Experts

Cindy Wells

Brad Brown

hsapiens

Are you a Sears Building Material Expert? Answer questions, earn points and help others

Manuals & User Guides

Keypad_Instructions_cl 976.pdf....

Related Topics:

Trustworthy Expert Solutions

Green light flashing 4 times,sencors lights on,press & hold wall button to open.others wont work

1 Answer

Anonymous

Add Your Answer

Attachments: Added items

Related Questions:

Merlin Prolift 230T wont clear / delete remotes from memory

How to Reset Your Water Filter Light

Error code 5100 check printer

Ink absorber full, ip2600

Xbox 360 power button light keeps flashing and disc tray does not open

Just wall switch works transmitters won't light

My garage door wont go down.I habe to hold the switch down but if i let it go the door will go up again.

Garage Door Wont Close Craftsman 1/2 HP (1998)

S9000 canon printer ink tank full

The remote opener reset button goes off and will not work

Not finding what you are looking for?

Craftsman LiftMaster Chamberlain Garage Door Opener Wireless Keypad Model 976LM Security+

Merlin Prolift 230T wont clear / delete remotes from memory

Related Topics

Ask a Question

Popular Questions

Garage door opens by itself

Sears craftsman 1/2 hp garage door troubleshooting

Garage door keypad code. How do I reset it?

Excessive opening force detected (code 42)

Lightning may have hit garage

Top Sears Building Materials Experts

Cindy Wells

Brad Brown

hsapiens

Are you a Sears Building Material Expert? Answer questions, earn points and help others

Manuals & User Guides

Keypad_Instructions_cl 976.pdf....