I have a LG toploader, turbo drum - fuzzy logic. It washes, but will not spin after the wash cycle, it drains, turns couple of times, fills with water , does it again. Gives a OE error message. Takes about 10 times to get it to spin cycle and then it does the same at the spin cycle, the OE error message keeps coming up.

6ya staff

• 2 Answers

SOURCE:

Hi there,
Save hours of searching online or wasting money on unnecessary repairs by talking to a 6YA Expert who can help you resolve this issue over the phone in a minute or two.

Best thing about this new service is that you are never placed on hold and get to talk to real repairmen in the US.

Here's a link to this great service

Good luck!

Instant Repair Help over the Phone

6ya.com

Save Time & Money by instantly connecting to...

Posted on Jan 02, 2017

SOURCE: Bowl keeps slowly filling with water when turned off.

I think your water valve is bad , change it

Posted on Aug 12, 2009

SOURCE: I want to remove my LG Fuzzy Logic WF-T8018Tp

.I am not a repair professional. I am a 78 year old man
who has been making his own repairs for about 50 years. So the washer or dryer ID doesn't mean much to me. I came to fixya looking for a schematic for an really old AM/FM radio and found that more than 4,700 people were asking for help with a washer repair. I recently had a washer repair of my own and at that time I found an excellent video which showed me how to take my machine apart. This video made it possible for me to do my own repair. If you are repairing a dryer or a front load washer I suggest you go to www.applianceaid.com where they have very good step by step trouble shooting and repair information on both washers and dryers as well as other appliances. If you have a direct drive top load washer and need help taking it apart this video is an early christmas present. I was so impressed with it that when I saw all these people needing help, I wanted to tell them about it. If you look at the back of your washer and the panel is solid (no small inspection plate to remove which would indicate you have a v-belt drive) chances are you have a direct drive and this video is just what you need. You can see it at www.acmehowto.com You will probably still need help in determining what the trouble is and how to fix it. After viewing the video or if you have a v-belt drive rather than a direct drive, I suggest you go to www.applianceaid.com where they have very good
trouble shooting and repair nformation on most
washers and dryers. I think you'll find what you need
there. Don't worry about the timer, they hardly ever
go bad. Good luck with it. If I have helped you, please rate my advice on fixya.

Posted on Dec 02, 2009

D. Floyd Kolb

• 43501 Answers

SOURCE: LG Top Loader Fuzzy Logic 5.5. The water

Hi,
No you just need to get the drain hose up higher...the water is siphoning out and is either caused by the end of the drain hose still in water and not having an air gap or the hose is not going up higher then the top of your washer...
Lifting the hose up should give you an air gap and get the hose high enough to stop the siphoning...

heatman101

Posted on Apr 28, 2010

Testimonial: "I am extremely impressed that this won't cost a call out service fee. . . and looking like a bimbo. thanks, heatman!"

Ginko

• 19396 Answers

SOURCE: my toploader "fuzzy logic" 6.5kg

Hi.

If there is no spin, c licking noise before spin may come from a relay in control module, from lid switch motor, or from the fuzzy logic control unable to start drain pump. This last problem may occur because of residual water inside the machine tub.

You should run a diagnostic cycle. The procedure is explained in user manual. LG should use the following:

Press Spin and Temp. and Power buttons simultaneously to enter diag. mode.

At the end of the process you should get an error code that will tell you what the problem is. If there is a code already, then please let us know the code.

Posted on Feb 01, 2011

SOURCE: Hi i have a samsung

It is probably not 1e but IE meaning input error. There is no water entering the machine. Could be the water valve. just in case check the inlet filter at the inlet valve to see it isn't blocked. then you will need to call for service www.thewashingmachineman.webs.com

Posted on Feb 23, 2011