Question about Televison & Video

1 Answer

Panasonic PT-51HX40B convergence issue

Hi,
I'm stumped trying to fix shot convergence on my Panasonic PT-51HX40B.
I replaced the STK-392-110's with no change in convergence.
I ordered and installed Sanyo STK-394-160's with still no convergence.
I checked all of the 20-ohm 1/10w resistors, values look good.
The voltages at the STk's look good.
I have no convergence control at all.
Any ideas or schematic would be appreciated.
Thanks,
Dan

Posted by on

  • Dan Smith
    Dan Smith Nov 15, 2008

    Replaced STK's with a new set. Still no convergence. Must be something else.

    If anybody has schematic or service manual, it would be helpful.

    Thanks,

    -Dan

×

Ad

1 Answer

  • Level 1:

    An expert who has achieved level 1.

  • Contributor
  • 4 Answers

Hi.....
Bit of a long shot but have you tried this??
http://oreilly.com/catalog/htheaterhks/chapter/hack12.pdf

Hope it helps!
Richard

Posted on Jun 30, 2008

Ad

1 Suggested Answer

6ya6ya

6ya staff

  • 2 Answers

SOURCE:

Hi there,
Save hours of searching online or wasting money on unnecessary repairs by talking to a 6YA Expert who can help you resolve this issue over the phone in a minute or two.

Best thing about this new service is that you are never placed on hold and get to talk to real repairmen in the US.

Here's a link to this great service

Good luck!

Posted on Jan 02, 2017

Ad

Add Your Answer

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

1 Answer

Picture out of line Problem with the Panasonic PT-53WX42 53 in. Rear projection. Possible convergence circuit? How do i change it


Picture colors lines R,G,B mis alingments,have colors shadows pictures or 3D pictures look alike?Yes.The tv convergence board is dead,the board require changes 2 STK convergence ICS and some or all of it resistors too.To fix the tv convergence board.U must have tools like a soldering iron,a desoldering pump or a roll of desoldering braids and also can do soldering work?Yes,tries websites like Tvrepairworld.com,Tvrepairkits.com to buy a convergence kit belong to ur tv model and make to repair it ur self.Or the shop will cost u like $300-350 for parts and labors.

Mar 23, 2011 | Panasonic PT-53WX42 53" Rear Projection...

1 Answer

PANASONIC PT-46G40U CONVERGENCE PROBLEM HELP...


Have you checked the bias resistors for Exact Value. They normally change value when the stk's take a dive.

Dec 09, 2009 | Panasonic PT-46G40 46 in. Rear Projection...

1 Answer

What causes this


Hi, thank you for visit fix ya.
Do you have problems with you STKs ICS convergence.
Replace stk 392-110, use stk 392-150 ( better).
For parts, go to:
http://www.encompassparts.com/
Thank you

Jul 23, 2009 | Panasonic PT-47WX49 47" Rear Projection...

1 Answer

Color registration doesn't fit. The Blue is hanging to one side and it's a bit wider


Color registration doesn't fit?? Do you mean that you have a convergence problem and that the colors are not aligning?
That set uses two STK392-010 and all low ohm the feed resistors out front of the amp should be checked for change in ohm value: R7051, 7050, 7049, 7048 all of them are 10 ohms 1/2 watt.
Bill

Nov 26, 2007 | Panasonic PT-51HX41 51" Rear Projection...

3 Answers

PANASONIC PT-51HX41E


The convergence amps have most likely failed. That unit takes two STK392-110 (Sanyo) amps. For more reliability I'd have them changed using an STK392-150. They have a greater amperage and higher heat tolerance.
It's clearly a job that you want a qualified shop to do.. Call around and get some off-the-cuff estimates on what they charge to change out the convergence amps and tell them that you would prefer they use the 150's instead of the 110's.. They'll probably wonder how qualified you are. :)
Bill

Nov 13, 2007 | Panasonic PT-51HX41 51" Rear Projection...

1 Answer

Panasonic Projection TV PT-47WX49E convergence ...


may not be convergence may be a bad stk for convergence if that style if so try stk

Oct 28, 2007 | Panasonic PT-47WX49 47" Rear Projection...

2 Answers

CONVERGENCE ic CHIP


if you can remove the rear panel assy. look for the convergence ic's they start with stk--- and you got the part number you need a source panasonic is 814 source and the number on the ic's stk 390 ----/

Aug 22, 2007 | Panasonic PT-53WX42 53" Rear Projection...

Not finding what you are looking for?
Televison & Video Logo

Related Topics:

208 people viewed this question

Ask a Question

Usually answered in minutes!

Top Televison & Video Experts

The Knight
The Knight

Level 3 Expert

76204 Answers

Cindy Wells

Level 3 Expert

6063 Answers

Marvin
Marvin

Level 3 Expert

85222 Answers

Are you a Televison and Video Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...