Girlfriend lost remote for RCA F27645. I know I

Without a remote controller, you may have limited options to change modes on your Apex digital TV. However, you may be able to change the mode by using the buttons on the TV itself.
Here are some general steps you can try:

1. Turn on your TV and make sure your DVD player is connected to it.
2. Look for the "Menu" button on the TV and press it.
3. Navigate through the menu options using the arrow buttons on the TV until you find "Input" or "Source."
4. Press the "Enter" button to select the input/source option.
5. Use the arrow buttons to select the input/source that corresponds to your DVD player.
6. Press the "Enter" button to confirm the selection.
7. Press the "Menu" button to exit the menu.

Note that the specific steps may vary depending on the model of your Apex TV. You may also consult the user manual for your TV for more information on changing modes without a remote controller.

SOME SETS have to have a remote
or on front of tv look for input or source button
or scroll through your menu and look for input or source

With the remote in TV mode, the input button on the remote should change the source (TV, AV1, etc. depending on the TV).

If the input button doesn't work, try a different code for your TV manufacturer. A code that controls the basic functions of the remote may not control the full set of functions of the TV. For some TVs, you can change the source from within the Menu. (It depends on the TV. I didn't notice if there was a Menu button that will open the TV menu on the RCA RCU600M.)

If none of the codes work, check if your TV has a Source or Input button on the unit. See if that button works.

If you have a different remote, please indicate the model.

I hope this helps.

Cindy Wells

on the remote there should be a button that says input, you can do it that way or there should be a button on your tv that says menu then goto the video settings and find the input

On the side of the TV there are a set of buttons. An Input button is next to the Menu button and will let you access the different sources connected to the TV. For the front panel input, look for the source labeled Front. (There are also volume control and channel +/- buttons.) The button order is Input, Menu, Vol -, Vol +, Ch -, Ch +.

If you want, you can get a substitute remote that is guaranteed to match the original remote's features here: http://www.remotes.com/remotes/servlet/rs?a=Search&o=c&uid=0&m=32V524T&uuid=12935850039140 .

I hope this wants.

Cindy Wells

Unfortunately, the Input button (to change the source from INPUT 1, INPUT 2,
INPUT 3, INPUT 4, Front Input, HDMI/DVI, and last-active channel) is only on the remote. If your universal remote was built 6 months after the TV was released, try a different code for RCA/Thomson TVs (assuming the remote has an input or source key). Thomson built the TV.

If your universal remote doesn't have an input key, you probably need a higher end remote (one with that key or one that can be programmed from a computer). Alternatively, you can get an exact replacement remote here: http://www.remotes.com/remotes/servlet/rs?a=Search&o=c&uid=0&m=HD52W58&uuid=12927154203570 .

I hope this helps.

Cindy Wells

I would suggest you try to find a universal remote that has an "input" or "source" button and program that one to your tv. By pressing the "source" or "input" button, it will change the input to the tv. I hope this helps! -Der Strom

install your cellphones with tv remote.. download that from www.mobile9.com.. you can use that to remote you TV.. depends on your cellphones..

using the menu button on the t.v. set an alarm for 1 min in the future. have the t.v change to channel 00 or the input channel @ that time. turn off the t.v and wait until the alarm turns the t.v on.

Yes, To change the input to video jacks, you must change the channel to 00.