Printer Setup & Support Call 1-(805) 225-6690 We are 24 Hour Available Call Now For Help

Power fluctuations
https://www.askmefast.com/MY_DSTV_DSD_3U_DECODER_IS_DISPLAYING_ONLY_ORANGE_STEADY_LIGHT-qna9330642.html

Or it might be dad service, or downloading new software

[Responded] Poor service / Decoder software removed ' DStv ...

www.hellopeter.com > dstv-multichoice > reviews > po...

Mar 14, 2018 - However, the problem escalated now whereby my DSD 3U DSTV decoder suddenly switched off and only display an amber light in the middle ...

Gotv decoder showing a yellow / Orange light constantly

myofflinestash.com > index.php > gotv-decoder-showi...

Solid Red This means that the decoder is in StandBy Mode, this is similar to a computer being put in sleep mode. · Solid Amber This state of the decoder means ...

Quick Guide - DStv

cdn.dstv.com > selfservice > documentation

PDF The moment you connect your DStv HD Decoder, is the moment your TV viewing experience will become ... Solid AMBER = decoder is downloading software.
..

Dstv Dsd 1132 Manual - PDFSLIDE.NET

pdfslide.net > Documents

Dstv Dsd 1132 Manual Dstv Dsd 1131 Decoder Manual can even captures a thumbnail and optional large screen Dstv Dsd 1131 Decoder Manual of a web site.

Try this qiuck solution as it works most of the time:

Switch off your DSTV Decoder or Unplug power supply cable at rear of Decoder.
Remove your Sim card and wait 90 seconds.
Switch your DSTV Decoder back on or plug Power supply cable back in at the rear of your Decoder.
Enter your Sim card and wait for your Decoder to re-scan (about 2 - 3 minutes).

movie channels are add on packages you need to pay for and next time notify dstv about your account

PROPHETIC CHANNEL SETTINGS on Your DECODER(DSTV)
Step: 1 Press menu Select "Advanced Options" Select "Dish Installation" Enter the pin "9949"
Select "Network Configuration" Select "Network 2 Setup" NB: Leave "Network 1 Setup (Home)" unchanged!! Set Signal Setup to "Enabled" by selecting it, and moving left or right Set Frequency to "11170" Set Symbol Rate to "26652 Set Polarization to "Vertical" Set FEC to "3/4? Select "Accept these settings"
Step: 2 Select "Network 2 Setup" Set Signal Setup to "Enabled" Set Frequency to "12682" Set Symbol Rate to "26657 Set Polarization to "Horizontal" Set FEC to "1/2? Select "Accept these settings"
Step: 3 Select "Network 3 Setup" Set Signal Setup to "Enabled" Set Frequency to "12722" Set Symbol Rate to "26657 Set Polarization to "Vertical" Set FEC to "1/2? Select "Accept these settings"
Step: 4 "Accept these settings" to go back to the "Dish Installation" menu then Select "Scan All Networks" Your decoder will go into scanning mode and might take a while to scan all networks. Do not interrupt the process even if it seams to take longer than you expected! Once completed, your picture will return as normal.
ENJOY WATCHING PROPHETIC CHANNEL.
http://electronicshelponline.blogspot.com/
http://schematicscom.blogspot.com/
http://electrotechnician.blogspot.com/

Main system control IC fault.

Hello,
The best that I can give you is at this link:
http://hopeafrica.tv/index.php/component/content/article/40-schedules/202-dstv .
It should be noted that Africa does not have digital tv so you should probably hook an antenna to the tv without the box and have the tv search for analog tv stations as that will stand the best chance of picking up what few channels they do have.
Good Luck!
Rich Lilja

here are 2 web sites that might be able to help you
https://www.facebook.com/MultichoiceAfricaInstallers/posts/335719336540810
https://sites.google.com/a/napro.ca/cathsat/dstv

and also a pdf manual
http://uec.co.za/manuals/DSD990/MCA%20DSD%20990%20User%20manual.pdf

i can not find very much on that model

If you have extra batteries, try to replace the old one and install the new batteries. And if still doesn't work, try to clean the battery terminals of the remote control, because sometimes, those are the one that making the problem due to corrosion caused by leaked batteries.

very simple ,, the tv next to the decoder must be conected using a rca cable and then run normal tv cable (RF out ) to the other room