Function of 4 setting/buttons Seiko SNJ018 Analog Digital Watch

Question moved from Lands Phones category.

SEIKO - A158 5040

Digital Watch Library http://www.digitalwatchlibrary.com > DWL > seiko-a1...

SEIKO - A158 5040 - Digital. Released in 1978 Vintage Digital Watch - Brought to you courtesy of digital-watch.com.

SEIKO QUARTZ Cal. A159 Alarm Chronograph

My Retro Watches https://myretrowatches.co.uk > uploads > 2020/09
The A158 Alarm Chronograph model can be set to give a time signal ... QUARTZ. ALARM-CHRONOGRAPH. START/STOP. DATE/SELECT. STOP-ALARM. WATCH SET TIME SET LAP STOP ...
3 pages

Missing: 5040A ‎' Show results with: 5040A

Instruction ' Seiko Watch Corporation

SEIKO WATCH https://www.seikowatches.com > customerservice > ins...
Seiko is one of the few fully integrated watch manufactures. We design and develop our own movements using leading-edge technology.

try here > http://www.seiko.co.uk/support/instructionbooklets h023 may be same

Hello,

Seiko watches are a popular accessory for both men and women. The history of Seiko watches goes back to 1881 long time ago, when the company that was to become Seiko began. From the beginning, the method to set a Seiko watch has been designed to be a simple process.

The following are the steps to set a Seiko watch for the time, day and date function, and for setting the chronograph on an analog watch.

Set the Time:

• THE CROWN

Pull the button on the side of the watch carefully, the crown, out to its most extended position. You will need to unlock the crown if your watch has a locking crown. To unlock, turn the crown counter clockwise. While the crown is pulled out in the setting position, the watch will cease functioning.

• 12 O'CLOCK POSITION

Turn the crown clockwise to move the hands of the watch past the 12 o'clock position on the dial. The day and date will change to indicate AM setting but will not change for PM setting. It is recommended that you set a Seiko watch in the morning for instant day and date setting; however,this can be done manually.

• FINISH

To finish setting the time, simply push the crown until it is flush with the side of the watch.

Good luck and thanks for using fixya.

Setting Digital Time

1. The digital timepiece on a watch is set using the function buttons on the outer part of the watch face. To set the digital time, press and hold the upper left button until the seconds starts blinking. Press the lower right button to reset the seconds to "00."
   
   Push the lower left button to move to the Daylight Savings Time portion of the watch. Use the lower right button to toggle between "On" and "OFF."
   
   Press the lower left button twice. The hours unit will start blinking. To advance the hour, press the lower right button repeatedly until the correct hour is displayed. If you need to move the hours unit backwards, press the middle right button until the correct hour is displayed. When the hour is set, press the lower left button to switch to minutes, and use the same commands to change the minutes unit.
   
   After the time is set, press the upper left button to exit the digital time setting function.
Setting Analog Time
2. You may find after setting the digital timepiece that the analog display does not match. When this occurs, you need to set the analog time. To set the analog time, press the lower left button 6 times. Next, press and hold the upper left button until the digital time starts to blink. This indicates that you are in analog time setting mode.
   
   Analog time adjustment is completed using the lower right button. Every time you press the button, the analog time will advance 20 seconds. If you need to make a big change to the analog time, press and hold the lower right button to make the hands move faster. Once the analog time is set, press the upper left button to exit the analog time setting mode.

mcdevito75 here, Your watch should start by pressing the MODE button maybe once or twice or by pulling out the stem as if to set the time and pushing it back in.

You can obtain instructions from the Seiko web site "seiko.com".

Go to their web site, click on "support". The on "instruction booklets",

You can either enter the number off your watch or choose the instructions from the list.

These are the instructions for the AD0721. They might apply to your model, too. I hope this helps:

http://img261.imageshack.us/img261/6784/manualr.jpg

The analog setting of the watch takes place by pulling out the knob (kind of tough) and adjusting, like a regular analog watch. The analog and digital displays are will NOT stay in sync, unfortunately.

Good luck.

PC

See the manual for the Oakley GMT. That watch uses the Seiko movement, and the buttons work the same. See http://www.oakley.com/pdf/analog/gmt_manual.pdf

You may can find instructions here:

http://www.seikousa.com/#FAQ

Go through the watches till you find the match.

Rate me, please.

you need to give the movement number. at seiko watches you will find a number which has 8 letters and/or digits devide by -