My screen doesn't turn on for more than .3 seconds when i push the power button. I'm not sure what to do.

Instructions

1. • 1 Switch the Canon MX310 off using the "Power" button, then push the "Stop/Reset" button on the control panel. Hold the button down for about five seconds.
     
   • 2 Push the "Power" button while holding "Stop/Reset." Hold down both buttons for five seconds.
     
   • 3 Release "Stop/Reset" while holding down the "Power" button.
     
   • 4 Push "Stop/Reset" twice while continuing to hold the "Power" button. Release the "Power" button. The power light will turn green.
     
   • 5 Once the light is steady green, push "Stop/Reset." Wait about three seconds and push it again. Wait three more seconds and push it one final time, for a total of three times. The power light will turn orange.
     
   • 6 Push the "Power" button, then lift the MX310 cover open.
     
   • 7 Remove both ink cartridges and wait 10 seconds. Replace the cartridges and close the MX310 cover. Wait 30 seconds.
     
   • 8 Push the "Power" button. Wait a few seconds to allow the printer to fully power down, then switch the Canon MX310 back on using the "Power" button.
     

1. All Operating Systems
   • 1 Remove any discs in the computer.
     
   • 2 Hold the power button down until the computer turns off.
     
   • 3 Press the power button to turn the computer on. If this doesn't work, proceed to step four.
     
   • 4 Remove the battery and unplug the netbook. Wait 30 seconds.
     
   • 5 Reinstall the battery and plug in the netbook.
     
   • 6 Press the power button for ten seconds. If this doesn't work, proceed to step 7.
     
   • 7 Insert the end of a paperclip into the reset button to reset the netbook. The reset button is a small hole that usually appears next to the USB and other ports.
     
   Windows 7
   • 1 Create a new Notepad file.
     
   • 2 Type this code:
     taskkill /F /IM dwm.exe
     
   • 3 Save the file as displayfix.bat in the following location: C:/ProgramData/Microsoft/Windows/Start Menu/Programs/Startup
     
   • 4 Restart your computer.
     

IMPORTANT NOTE:
You must have the security anti-theft code for your VW radio from the car manufacturer, or from a VW dealer!

You can find the radio code at: http://www.radio-code.co.uk/

The sequence of VW radio gamma programming is:
1. Push simultaneous "SCAN" and "RDS" keys until on the screen will appear "1000" displayed.
2. Release keys. No more push on "SCAN" and "RDS" keys because otherwise number "1000" will be considered as first safe code attempt.
For example: we have the security code "5079". Then:
3. By the no.# 1 key you will set up the first safe code digit. Push 5 times on the no.# 1 button. The "5" number will be setted.
4. By the no.# 2 key you will set up the second safe code digit. Push 10 times on the no.# 2 button. The "0" number will be setted.
5. By the no.# 3 key you will set up the third safe code digit. Push 7 times on the no.# 3 button. The "7" number will be setted.
6. By the no.# 4 key you will set up the four-th safe code digit. Push 9 times on the no.# 4 button. The "9" number will be setted.
7. Then push again simultaneous "SCAN" and "RDS" keys for confirm this safe code. On the screen will be displayed "SAFE" notice. Release keys! For few seconds a radio frequence will be displayed.
The radio is now ready for use!

I think that's Demo mode.
I got stuck there too.

This is what worked for me:

1. Power the radio off (hold the power button in top left corner in for several seconds)
2. Remove face plate
3. Hold in reset 10 seconds
4. Press push-menu dial/button 3 or 4 times
5. Insert cd and hit source to switch to tuner before cd starts

Not all of these steps may be necessary.
I suspect having the power off before the reset button was the important part.

Have you tried this?

1 - Turn on TV and set input to port being used.
2 - Make sure PS3 is connected via correct cable.
3 - Power on PS3 via power button and HOLD IT for 5 seconds (release after the second beep). It should automatically configure your PS3 to the TV's native resolution for all settings.

If this doesn't work, it may need to be repaired. A good place to try is www.videogame911.com. They do really fast work and save all your data.

Hi,

If the printer powers on and stays Idle with HP logo screen, you try reset the printer as below (try next step one after the other, if it doesn't fix)

Power Drain:

• Turn OFF the printer, disconnect the power cable from backside of the printer and from wall outlet.
• Press and hold the Power button for 60 seconds.
• Connect the cable and turn ON the printer.

Partial Reset

• Remove the power cable from back side of the printer while its ON.
• Press and hold "#" and "3" button, while holding them both insert the power cable and release the button after 10 seconds.
• If printer turns OFF, press power button to turn it ON.

Semi-Full reset

• Remove the ink cartridges.
• Remove the power cable from back side of the printer while its ON.
• Press and hold "#" and "6" button, while holding them both insert the power cable and release the button after 10 seconds.
• If printer turns OFF, press power button to turn it ON.
• Insert the ink cartridges.

NVM Reset

• Remove the ink cartridges.
• Remove the power cable from back side of the printer while its ON.
• Press and hold "OK" and "Cancel" button, while holding them both insert the power cable and release the button after 10 seconds.
• If printer turns OFF, press power button to turn it ON.
• Insert the ink cartridges.

Regards
Riztech

1 - Turn on TV and set input to port being used.
2 - Make sure PS3 is connected via correct cable.
3 - Power on PS3 via power button and HOLD IT for 5 seconds (release after the second beep). It should automatically configure your PS3 to the TV's native resolution for all settings.

Try these 3 resetting steps:
1. Push the "Power" switch downward into the "Hold" position.
2. Press and hold the "Menu" and "Record" buttons at the same time until the device resets.
3. Push the "Power" switch upward all the way to turn it back on.
OR
1. Grab a steady hold around the device.
2. Push the "Power" upward and hold it there until it powers off.
3. Power the device back on by releasing the power switch and then pushing it upward again.
OR
1. Unscrew the screws on the back of the device (or simply push the lid off if it is a model without screws.)
2. Take out the batteries from the slot and wait until the screen goes black.
3. Insert the batteries the same way they were mounted and attached the lid again.
4. Push the power switch upward to turn on the device.

Hold the Vol+ Vol- buttons down and turn on the power switch in the back of the unit.
The screen should turn blue and some square in the middle of it.
The noisy square is actually the bios being reset.
Once the unit turns itself off, you can turn it back as usual.
Note: Some of these units require a 3 button reset.
In that case hold Vol+ Vol- and Menu at the same time while you turn the power switch on in the back of the set.
I hope it was helpful.

Power off phone. Press and hold Green, * and 3 and keep them held whilst powering on and for a few seconds after
man the code written is hard reset for n95 **** .there is a hardware problem in the cell phone you need to change the strip of ur cell phone which connect the upper and lower portion.