How to print auditron report (copy) from workcentre pro 128? Need step by step instructions- have no manual

Unfortunately Xerox doesn't have a Yosemite driver for the WC Pro 123. Here is the driver compatibility chart. http://www.office.xerox.com/latest/SFTDS-01U.pdf
You may want to try the 10.5 driver
http://www.support.xerox.com/support/workcentre-pro-123-128/downloads/enus.html?operatingSystem=macosx&fileLanguage=en

Service manual, registration required:

https://www.scribd.com/doc/131575367/WorkCentre-123-128-133-Service-manual

http://www.copytechnet.com/forums/xerox/66901-error-041-366-document-centre-286-a.html

The Auditron feature is used to prevent the machine from being used by unauthorized users and also to track the total number of copies or prints produced with each account. When the total number reaches the upper limit set up by machine administrator, users cannot use the copy feature on the machine. Before resetting the machine you will want to print a usage report. Those instructions are at the bottom of these instructions.

1. Press the [Log In / Out] button on the Control Panel. See the Related Items below for additional information on navigating the Control Panel.
2. Press the [Select] button below the Display Screen to select 'System Settings.'
   
   
3. Use the numeric keypad on the Control Panel to enter the Administrator Login ID, then press the [Select] button to confirm.
   
   NOTE: The default System Administrator Login ID is set to 11111. The System Administrator mode allows you to customize many settings on the machine to suit your particular requirements. The machine enters the Machine Administrator mode only when a correct System Administrator login ID is entered.
   
   
4. Press the [Select] button until 'Auditron Admin' is highlighted, and then press the [Enter] button on the Control Panel to confirm selection. The Auditron Administration screen will be displayed.
5. Press the middle [Select] button until 'Reset Acc Limit' is highlighted, and then press the [Enter] button. The 'Reset Accounts' screen will be displayed.
6. Press the left [Select] button to reset all accounts.
7. Press the middle [Select] button to cancel the request.
8. Press the left or middle [Select] button to perform the action. The Auditron Administration screen will be displayed.
9. Press the [Exit] button to return to the default screen.

Solution : How To Print Reports and Lists (Auditron / Copy Meter Report) The Print Report / List feature allows you to print various reports and lists for each non-print job.

1. Press the [Machine Status] button on the Control Panel. The Machine Status screen will be displayed on the Display Screen. See the Related Items below for additional information on navigating the Control Panel.
2. Press the middle [Select] button below the Display Screen to display the Report / List information.
   
   
3. Press the [Enter] button on the Control Panel. The Print Report / List (Non-print Jobs) screen will be displayed with the options referenced in the table below.

Copy Meter
Lists the account data such the account name, the limit set for the account and the total number of copies for each account.

1. Press the [Select] button to scroll to highlight the required report under the appropriate column, then press [Enter].
2. Press the [Start] button on the Control Panel. The Report / List will print.

Try Global drivers, maybe work in yoe case. In search put Global Print Driver, then Drivers & Downloads.

GL
Jefferson, Fortaleza-Ce-Brasil

Re check all the connections. When taking off the paper feed assay, other parts and plug and jack connections were needed to be taken off first.
Make sure the drum seats in its correct position, silver grounds are not bent.
The copy cartridge and Dev housing are not connecting very good somewhere.
Make sure the machine is unplugged.
Try running copies.

Take a piece of copy paper, and some alcohol or some glass cleaner.
Lift the document feeder and clean that 1 inch strip of glass on the right side. It may even be a mark on that glass you cant see.
But the copy paper and alcohol will create enough cleaning and firction to remove whatever is on there.
It just has to be a small dot of ink or dirt in the right spot on that glass.

That is a software related error, You most likely need to reload the firmware, or replace the hard drive.
You can try disconnecting all the document feed and scanner cables then reseating them. Other than that, your looking at a software issue.

this should get you to the right area. I think you are asking to read the auditron accounts. This is the reset, which will allow you to see the copy count for all accounts set up.

The Auditron feature is used to prevent the machine from being used by unauthorized users and also to track the total number of copies or prints produced with each account. When the total number reaches the upper limit set up by machine administrator, users cannot use the copy feature on the machine. When the Auditron feature is enabled users need to enter a password to display the System Settings screen, or use the Copy, Fax and E-mail features on the machine.

1. Press the [Log In / Out] button on the Control Panel. See the Related Items below for additional information on navigating the Control Panel.
2. Press the [Select] button below the Display Screen to select 'System Settings.'
   
   
   
   
3. Use the numeric keypad on the Control Panel to enter the Administrator Login ID, then press the [Select] button to confirm.
   
   NOTE: The default System Administrator Login ID is set to 11111. The System Administrator mode allows you to customize many settings on the machine to suit your particular requirements. The machine enters the Machine Administrator mode only when a correct System Administrator login ID is entered.
   
   
4. Press the [Select] button until 'Auditron Admin' is highlighted, and then press the [Enter] button on the Control Panel to confirm selection. The Auditron Administration screen will be displayed.
5. Press the middle [Select] button until 'Reset Acc Limit' is highlighted, and then press the [Enter] button. The 'Reset Accounts' screen will be displayed.
6. Press the left [Select] button to reset all accounts.
7. Press the middle [Select] button to cancel the request.
8. Press the left or middle [Select] button to perform the action. The Auditron Administration screen will be displayed.
9. Press the [Exit] button to return to the default screen.

http://www.support.xerox.com/go/results.asp?Xtype=docs&prodID=WC7328_WC7335_WC7345&Xlang=en_US&Xcntry=USA&prodName=WorkCentre%207328/7335/7345/7346

Btw, I’m available to help over the phone in case u need at https://www.6ya.com/expert/normanj_7893313f0751935f

Solution Title: How to print on COM10 envelops from the Bypass tray (PCL6) using a Windows 2000 O/S Resolution/
Solution Fixed! Did not fix. Resolution Role: Fix
Critical Message: The Envelope must be placed in the Bypass Tray face down (flap side up) and Long Edge IN. In Microsoft Word (Word 2000)

1. Under the Tools tab, select Envelopes and Labels.
2. Enter your Delivery and Return addresses.
3. Click on Options
4. Under Envelope Options; [Envelope size], select Size 10 (41/8 x 91/2 in)
5. Under Printing Options, select Portrait (LEF) - Long Edge Feed
   • As Feed from, select Tray 5 (Bypass)
6. Click <OK>

Within the WorkCentre Pro 123/128 print driver
After opening up the print driver [<Start>, <Settings>, <Printers>, double-click on the WCP 128 PCL6 driver], click on Printing Preferences under the General tab.

• Under the Paper/Output tab

Set the following features as follow:

• Job Type: Normal Print
• Paper Size: COM10
• Output Size: Same as Paper Size
• Image orientation: Portrait
• Image Rotation: OFF
• 2 sided Print: 1 sided Print
• Stapling: None
• Output destination: Center Output Tray
• Offset Stacking: None

• Under Tray/Layout

• Set Paper Source to Tray 5 (Bypass)
• Click on Bypass Tray Settings
  • Paper Type: Heavyweight (1 or 2)
  • Feed orientation: Portrait
• Click <OK>
• " on Specify Paper Type and select Heavyweight (1 or 2)
• " (Apply> and <OK>
• " <OK> again

In Microsoft Word under Envelopes and Labels, Click <Print> to send the information to the printer.

Note: This setup represents one way of printing envelopes. Other ways setting up some features in a different manner will work as well.

Solution v1.3.20.0 312637.How to Print on COM10 Envelops From the Bypass Tray (PCL6) 2006-04-05 21:57:29