My n70's back camera is not working properly.it take several minutes to be activated.if it is activated.itis stopped with in one second.my bluetooth is not also working properly.plese help me?

Found this online. Hope it helps you out.

Switching the headset on
To switch the headset on:
Press and hold the Play/Pause button for 2 seconds.
An ascending confirmation beep is heard in the headset and the LED indicates the current operating mode. Flashing in blue indicates that the battery charge status is OK; flashing in red indicates a low
battery (see page 6).
The LED flashes several times every second:
The headset is paired to one or several Bluetooth devices and tries to connect to one of these devices.
The LED flashes slowly (once every second):
The headset is paired to one or several Bluetooth devices. However, there is no current connection because the
Bluetooth device is switched off or out of range.
The LED flashes once every 3 seconds:
The headset is paired to one or several Bluetooth devices. However, there is neither an audio transmission nor an active call.
The LED is glowing slowly every 4 seconds:
The headset is paired to one or several Bluetooth devices, a sound file is received via A2DP and played back or
paused.
The LED flashes once every second:
The headset is paired to one or several Bluetooth devices and there is currently an active call.
If you switch on the headset and keep the Play/Pause button pressed for 5 seconds, the headset will go into pairing mode (see ?Pairing the headset? on page 9).
The LED flashes alternatingly in red and blue for up to 60 seconds:
The headset is not yet paired to any Bluetooth device. Pair it as described under ?Pairing the headset? on page 9.

The Err message alone indicates that a malfunction has been detected, and the manual recommends to fire the shutter and check for the message to clear. If it does not, to contact a Nikon Service Rep.

If it is Err + E, the film did not advance properly and needs to be reloaded.

take the battery out, leave for 2 minutes then put it back in and see how that goes

because it is not the factory settings which cause the problem,, it is the software itself, the only solution of that is to reformat

turn on cell phone. activate bluetooth. press right button to search for bluetooth devices. Then press the on button and the volume UP button at the same time on the Jabra headset. The cell phone then finds the device. put in the password/pin (usually 0000). and voila! it works

you need to go technician then ask them to reformat your n70 phone,so that it will work well.

Network code 23415000 Vodafone; United Kingdom.
IMEI 358637014464223
Phone model: Nokia N70

To enter the code to the phone (switch on without SIM card).
Input the Code in the phone as follows:

Your code's are:

#pw+089553613737057+1#
#pw+447937471501734+2#
#pw+949472576726771+3#
#pw+004003133262404+4#
#pw+449977373741273+5#
#pw+829031751772532+6#
#pw+878801503630103+7#

First code in the end of the string must be added + 1#
Code number 7 in the end of the string must be added + 7#

If you have proper software and You know on which lock, phone
is closed just simply enter proper CODE.

If YOU DONT KNOW – which lock is closed do the following:

1. Enter the first code, if it’s the wrong code – WAIT 30 seconds!!! And then:
2. Enter the code number seven this will open all locks.

How to get ‘p’ ‘w’ ‘+’ signs?
Press * several times on keyboard of phone.
Now a message should appear something like “Sim restriction off”. That means your phone is now unlocked.

!!Warning!!
If the codes don’t work after entering 5 codes You will lock the ‘CODE UNLOCK FUNCTION’ and it will be possible to unlock the phone only by using a cable/device.

it seems like u have a soft problem so u should better take that phone to a nokia asistance...

Hi
You can reformat your unit.. just follow this instructions. just off the fone then, press together the key no. 3 Astiris and phone in.. press in sustained position then turn on the power switch then you can see your fone is starting to refurmat...

I had the same problem, and this is how I fixed it. Now it's working fine.


Thank you for contacting Garmin International,

If you are currently running the most current version of bluetooth software, and you are still seeing issues where your compatible phone is still not connecting properly, please try the below procedure, which will reinstall the version of bluetooth you have downloaded in case there was any corruption during the transfer or installation of the bluetooth version.

1. Power the unit on

2. Touch View Map

3. Touch the ETA/Speed button in the bottom left hand corner.

4. press and hold your finger over the speedometer for 10-15 seconds until a new screen appears.

5. Touch next at the bottom of the screen until the top blue banner reads Bluetooth Status.

6. Touch UPDT P, then Touch yes.

7. At this point the unit should go to a page that says Updating Bluetooth Firmware, allow this to finish, once finished, press quit, then press and hold the back button. At this point, go back through and try to connect your Bluetooth device again.