Washing machine stops half way thru and flashes code LD?

Whirlpool Cabrio Washer Error Codes & Repair Help

applianceassistant.com/Washer.../Cabrio-Bravo-Oasis-Error-Codes.php

Whirlpool Cabrio Washing Machine Error Code Problems, Diagnostics, ... Cabrio LdError Washer is taking too long to drain water from the washtub

Kenmore Elite Calypso Top Loading Washer - ApplianceBlog

www.applianceblog.com/.../1297-Kenmore-Elite-Calypso-Top-Loading-...

Sep 11, 2005 - 10 posts - ‎5 authors
My washing machine stopped after filling and won't wash, drain or spin. ... and then come up with either LD, FL Or SL code and stop working.

Whirl Pool Cabrio LD Temp fix pt.2 - YouTube

? 2:59
https://www.youtube.com/watch?v=tFBtD2wUj4g
Jun 21, 2009 - Uploaded by liquid131
Whirl Pool Cabrio LD Temp fix pt.2. animal131 ... How to override an error code on the Whirlpool Cabrio washer - Duration: 3:08. Whirlpool ...

Ld - Long drain - Ld flashes if it takes longer than 5 minutes to pump out water to a point where the operating pressure switch resets. Press STOP/CANCEL to clear the display.

Ld = all water level lisghts flashing slowly accompanied by 5 fast beeps every 4 minutes - LID is open position

got this out of machine manual hope it helps

"Ld" (Long Drain) flashes
Is the drain hose kinked or clogged?
Press STOP/CANCEL to clear the display.
• "CA" or "Cl" (Current Limit)
Is the washer overloaded?
Press STOP/CANCEL to clear the display.

Here is a manual:

http://www.managemyhome.com/mmh/lis_pdf/OWNM/L0102048.pdf

See page 17.

Hello, LD stands for long drain.
If all the water isn't out of the unit within a certain time, the ld will flash.
Could be 2 things.

1) There's lint stuck in the pump preventing the water to drain properly or

2) You're using too much soap causing lots of suds also preventing the pump from draining properly. If this is the case, what you need to do is run the washer on full load with no detergent and clothes. Let it go thru the cycle and get rid of eccess suds. This is most likely your problem.

Best of luck :)

Ld" flashes if it takes longer than 5 minutes to pump out water to a point where the operating pressure switch resets.

Press STOP/CANCEL to clear the display.

harborstuff,
The code on your machine stands for 'Long Drain'. Ld flashes if it takes longer than 5 minutes to pump out water to a point where the operating pressure switch resets. I would bet that the bath mats left a bunch of stuff stuck in the recirculation pump hose, or pump itself, and the water cannot be drained fast enough. Check the intake and exit hoses of the recirc pump. It's easiest to get to the pump through the front panel of the machine(click here). Looks like this: click here. Hope this helps.
(Definitely get under there and check to make sure the pump hoses are not clogged. At $129 it's an expensive fix for a $10 bath mat that clogged up the hose with fuzz. 'know what I'm sayin'' :o) )

-samson39

BTW, I have the maintenance manual & have experience at replacing the recirc. pump, control board, motor board, touchpad, & lid switch so far.

ld sure sounds like lid switch problems. Suprised to see this so soon, but I did see one come apart on a fairly new Whirlpool. Luckily, it should be easy to check. Unplug the machine first.

Ld Long drain "Ld" flashes if it takes longer than 5 minutes to pump out water to a point where the operating pressure switch resets.

Press STOP/CANCEL to clear the display.

The washer drew half a tub of water on the "Bulky items" cycle, and stopped. All the lights on the cycle dial light up and flash, the machine beeps and the me error message in the "estimated time remaining" field is "Ld". I've tried to shut the machine down and change the cycle to "drain and spin" but it will not agitate, won't drain or spin.