COMPRESSOR NOT ON - Whirlpool ES5FHAXS Side by Side Refrigerator

Non detergent 30w mineral or synthetic

You need special tool
Tools Required ?€¢
J 37872 Compressor Clutch Holding Tool

?€¢
J 6083 Snap Ring Pliers

Important: Remove the three adjustable dowels from the J37872 Compressor Clutch Holding Tool.
Install three 5/16 x 1 inch bolts in place of the dowels.
Remove and discard the compressor clutch plate bolt.
Use the J 37872 to hold the compressor clutch plate from turning.
Remove the compressor clutch plate from the compressor.
Remove the compressor pulley snap ring using the J 6083
Remove the compressor pulley from the compressor.
Remove the compressor clutch coil snap ring using the J 6083 .
Remove the compressor clutch coil from the compressor.
google J 37872 - to see tool !

Air Compressor Trouble-Shooting, Problems, The Causes ...

www.portlandcompressor.com/compressor/trouble-shooting.aspx

Provided below is a general list of common air compressor problems, and a few quick ... Loose pulley, flywheel, belt, belt guard, cooler, clamps or accessories. ... Piston rings installed up-side down. ... Receiver does not hold pressure when compressor is unloaded. ... Turn on power, check fuse, breaker, or motor overload.

Reasons Why an Air Compressor Will Not Build Pressure

fix-my-compressor.com/compressor-will-not-build-pressure/

An air compressor that will not build pressure runs on long past the point where it normally ... air compressor with at least one piston that moves up and down or side to side to pump air - cycles, .... I have an Ingersoll rand 7100 compressor 2stage 175 psi 120 gal tank ... The motor is a 2.5hp 3450 rpms with a 4 inch pulley.

Supercharge your Air Compressor for 20 bucks or less - Sawmill ...

www.sawmillcreek.org > ... > General Woodworking and Power Tools

Mar 16, 2006 - 15 posts - ‎8 authors
I have a 27 gallon belt driven Sanborn (Coleman) compressor and I have been ... I'mnot suggesting they won't compress air or give good service. .... Most any small oil-less compressor will serve a nailor, pump up the snow tires ... A two stagecompressor pumps 20 to 30% more CFM per motor HP thanks to ...

COMPRESSOR REPLACEMENT



REMOVAL PROCEDURE

1. Recover the refrigerant Refer to Refrigerant Recovery and Recharging.
2. Remove the washer solvent container.
3. Remove the air cleaner resonator outlet duct.
4. Remove the cooling fan and shroud.
5. Remove the accessory drive belt from the A/C compressor.

1. Remove the compressor hose assembly nut from the compressor.
2. Remove the compressor hose assembly from the compressor.

IMPORTANT: Remove and discard the sealing washers.

1. Remove the upper A/C compressor mounting bracket bolts.
2. Remove the lower coolant hose.
3. Raise and support the vehicle. Refer to Vehicle Lifting.
4. Disconnect the A/C compressor electrical connector.
5. Remove the lower A/C compressor mounting bracket bolts (3).
6. Lower the vehicle.
7. Reposition the compressor and mounting bracket to access the remaining compressor to bracket bolts.
8. Remove the upper A/C compressor mounting bolts (4).
9. Remove the A/C compressor.
10. Remove the A/C compressor bracket.

If the compressor came on when you were testing it with a test light, it sounds like something is wrong with your ground for your compressor, and completely the circuit through your test light.

Couple Video How To Replace Compressors. I Think Its Not DIY.
Hope Thats Helps.

Hi, did you change, capacitor for compressor too. check compressor overload switch,(relay) normally located on compressor terminals, (where you connect wires to compressor) that's the device that goes klix when compressor goes to start, could be faulty, or maybe low voltage from your mains(house panel) check line voltage, with digital volt meter, some compressor won't start if voltage drops to low, yes fan will work, could also be, your compressor has a lock rotor, (hard start), you can buy a compressor hard start kit, from appliance store, and try to start compressor, or maybe compressor internal winding, are damage, especially now in summer, when you got a lots of voltage drops, check compressor winding, check compressor winding for short circuit, remove cover on compressor, remove 3 wires from compressor terminal, use ohm meter, put one tester lead on copper tubing that's connected to compressor, and next lead to compressor terminal, one by one, if you get beep (continuity) from anyone of those compressor terminal, you got a short- circuit in compressor, you will have to replace compressor, but if there's no short, them try hard- start kit, replace overload relay, you will see it at compressor terminal location, after you remove cover. good luck.

Unfortunately, the cost to replace just the compressor unit is not much different than replaceing the entire unit.