Bissell 3510 Vac with loud noise but not belt

They are all called 'Navigator' :>D
https://www.google.com/search?q=Shark+Navigator

When switch to carpet, the difference is that the brush roller turns. When it is on hard floors setting it doesn't. Remove the base plate, remove the brush and the belt. There is likely something wrapped around the drive spindle or clutch.

How to reduce high pitch noise of Shark vacuums

Digital Trends https://www.digitaltrends.com > Smart Home > Guides
Apr 6, 2022 - You can adjust the height on a Shark vac to accommodate certain levels of rugs, carpet, etc. If the vac has been set too high for the current ...

Loud rotating carpet brush noise: Just got my new Shark

Fixya https://www.fixya.com > support > t15932203-loud_r...
It seems that your drive belt for the beater brush is stretched. This is a common problem -- if you flip the vacuum over so you are looking at the bottom, you ...

4 Reasons Why Shark Vacuum Is Making Noise

howtofixit.net https://howtofixit.net > shark-vacuum-making-noise
Aug 20, 2021 - Another cause behind the loud noises coming from your Shark vacuum is an overly dirty or damaged filter. Remember: air must be able to pass ...

‎Loud Or High Pitch Noise · ‎Blockages · ‎Rattling Noise · ‎Belt Snapped In Powerhead

Does anyone know why my vacuum might be making a ...

Reddit · r/VacuumCleaners 10+ comments · 2 years ago I agree, suction relief valve is popping because of a blockage. Check the extension wand too. The air goes from floor head, lower hose, ...

6 answers · Top answer: That's the suction relief valve. There is a blockage somewhere in the system, either in the ...
Loud Air Coming Through Side Vent, Brushroll Not Spinning
Dec 4, 2020
How to fix this without taking it in? Shark vacuum - Reddit
Sep 27, 2022
Shark making weird suction noise : r/VacuumCleaners - Reddit
Aug 13, 2022
Shark Vacuum Making Strange Noise and Not picking up Dirt
Sep 22, 2022
More results from www.reddit.com

Motor cooking dust

Try not to **** up any more water. Don't use until you can dry it out well. Hopefully you live in a warm climate so that will happen sooner than later.

try this link
http://www.vacsite.com/en/bissell-parts-1/bissell-parts/3576-cleanview-ii-bagless.html

you can get a free manual at manualsonline.com
I just looked up your vac on page 5 of their list of manuals. Or you can open up your vac and see how the belt is on there and then you will see how to do it --- or you can take it to a vac repair shop and get them to replace it for about $12-15.

Hope it helps.
Kris

if its over a year old junk it if not it would be under warranty

You can get the belt you need for the Easy Vac here:

Bissell Easy Vac Replacement Belt

And here is a link to the manual

Bissell Easy Vac User Guide (PDF)

Sounds like the brush roller is worn and making noise, take the complete vac to the repair shop for service. I've seen this cause damage to the front nozzle housing as well.

I’m happy to assist further over the phone at https://www.6ya.com/expert/robert_b96ba3f038cf317c

Hi,
According to Bissel, they should be standard phillips screws. Nowever - things change.
This is a general guide from Bissel for belt change -
BELT CHANGE _ CLICK HERE

Check your model number on that site for exact details.

If the screws are Torx (star) or other security screws, tool bits are available from Screwfix -
SECURITY SCREW BITS
That fit standard loose-bit screwdrivers.

Hope that solves your problem.
Thank you.

turn vac over, take of the access plate covering the brush roll, may be 2 to 4 screw. Then you can get to the brush roll and belt. It uses a Bissell Style 7 belt.