Wireless sensor quits working

Question edited for a LOT more clarity. full 'make model (what it is)'.
Question moved from Computers to Model category.

Remove the batteries from both indoor and outdoor unit. Leave them out for 10 minutes. Replace the outdoor sensor with a new battery (2xAA), and then new batteries in the main unit (3xAA).

00605 Wireless Weather Station + Companion Instructions

AcuRite https://www.acurite.com > media > manuals > 0... PDF NOTE: When replacing the batteries for the wireless sensor, remove the batteries from the sensor and clear that sensor's channel on the main unit by pressing ...
6 pages

Hard Reset for Sensor Models 00606TX/06009RMA1 & ...

AcuRite https://support.acurite.com > en-us > articles > 360007...
The following reset steps can be performed to correct issues of the sensor not connecting to the display. Symptoms of the sensor not...
https://fccid.io/RNE00605TX/User-Manual/User-Manual-707183

..

[PDF]WS-8117 ATOMIC CLOCK WITH OUTDOOR WIRELESS ...

https://www.lacrossetechnology.com/products/.../misc/8117-manual.pdf

NOTE: Do not set the clock until the outdoor temperature is displayed. .... The unit will still try and receive the signal every day despite it being manually set. ..... sunlight, extreme cold and wet/moist conditions as these will lead to rapid changes ... Beforesending the atomic clock in for repairs, contact La Crosse Technology.

La Crosse Technology Top Solutions

https://www.lacrossetechnology.com/support/top_solutions.php

A: Complete a restart for display with the temperature/humidity sensor: ... to rest for 15 minutes can result in failure to connect with the outdoor sensor or missing ... Products set outside of these time zones will not search for a WWVB signal as it is ... locate the Clock or Weather Display near an outside wall and point the unit in ...

Common issues weather stations: Click Here

www.weather-station-products.co.uk/faqs/common-issues-weather-stations

Under £30 £30-£75 £75-£125 From £125 Birdhouses/Feeders Outdoor Clocks ... I'mnot getting any outdoor readings from my outdoor sensor, what do I do? This willcure 90% of all sensor connection problems, important you must ... is the airtemperature, to get this reading you need to place the unit away from direct sun.

Replacement Temperature Sensor ' AcuRite

www.acurite.com > All products

http://www.manualslib.com/manual/768624/Acurite-00837w1.html


user manual can tell you

or
http://www.acurite.com/5-what-to-wear-digital-weather-station-with-forecast-temperature-humidity-clock-00837w1.html


go too the support site !!!!

all else fails read the instructions!!!

have a nice crimbo pls

Hi Jerry,

While lithium batteries are recommended for the outdoor sensor it is not recommended they be used in the indoor display unit. Try using a good quality, fresh alkaline batteries and you should find your display turns back on.

http://www.acu-rite.com/product-manuals.html
http://www.ehow.com/way_5552159_acurite-atomic-clock-setting-instructions.html
Please find what you want at the above links....

How do I change the clock from 24hr to 12 hr?

Before attempting to set the time, let the outdoor transmitter sync with the indoor receiver. Once that's done, you'll be able to successfully set and retain the date and time.

Double check the batteries to make sure they are installed correctly. If one of the batteries in the outdoor sending unit is in backwards, it will not send the outdoor data. On the indoor unit, there is typically one battery that is used for receiving the signal from the outdoor unit. If all of the batteries are in correctly but that one, you will see the display and the indoor temperature information, but the outdoor information will not be displayed.

I just found my manual for the Acu>Rite Wireless Weather Thermometer Model #00616, do you still need directions?

take a look at Chaney Instruments http://diplodocs.nl/references.php

Wireless Thermometer with Sensor
Model 00735 ??