Jamming of documents in autmatic feed for scan mode

Hi Try this method

To "Settings/Registration Table"

You can specify the method for restarting scanning of documents when a paper jam occurs in the feeder.

For information on the optional products required to use this function, see "Optional Products Required for Each Function."

1. Press (Settings/Registration) ? [Function Settings] ? [Common] ? [Scan Settings] ? [Feeder Jam Recovery Method].

1. Select [From 1st Page] or [From Stopped Original] ? press [OK].

Details of each item are shown below.
[From 1st Page]: If a paper jam occurs in the feeder, scanning starts again from the first page of the document. [From Stopped Original]: If a paper jam occurs in the feeder, scanning starts again from the page of the document scanning was interrupted.

Hi nigel_lester,

This error message "Document in ADF" that you are getting means that you need to remove foreign object from the Automatic Document Feeder (ADF). Kindly follow the procedure below in clearing document jams:

Document jams in the ADF (Document Tray)

1. First, press Stop/Reset.
2. If a multi-page document is loaded, remove any documents other than the jammed page from the ADF. 3. Then, open the Feeder Cover.
4. From under the roller to the Feeder Cover side, remove the jammed page.
5. If a document is not jammed, check the document feed area if there's foreign material. If there's any, carefully remove it.
6. Close the Feeder Cover.

NOTE:

• If documents remain in the ADF after pressing during scanning, [Document in ADF] will appear on the LCD. Press so that the remaining document is automatically fed out.

• When rescanning the document after clearing the error, rescan it from the first page.

Document jams in the ADF (inner side)

1. Press Stop/Reset.
2. If a multi-page document is loaded, remove any documents other than the jammed page from the ADF, then open the Feeder Cover.
3. Raise the paper release lever (A) then remove the jammed page from under the roller to the Feeder Cover side.
4. Open the Document Cover and pull out the document from the inner side.
5. Close the Document Cover.
6. Close the Feeder Cover.

Note: When rescanning the document after clearing the error, rescan it from the first page.

Hope it helps.

Thank you for using Fixya.

Instructions

1 Lift the hatch on the feed tray and pull up the large green tab to the left of the roller. Remove any jammed or torn paper from under the roller and around the feed tray.
2 Pull the input feed tray out of the automatic document feeder. Grasp the feed tray with both hands and pull it straight out.
3 Check the interior of the automatic document feeder for jammed paper. Remove any jammed paper, then reinsert the feed tray into the automatic document feeder. Push down the feeder cover until you hear a click.

Paper jams - Kodak Printers

Issue: ERROR LCD: DOCUMENT IN ADF
Solution: Remove foreign object from the Automatic Document Feeder (ADF) - MX310
Check the Automatic Document Feeder (ADF) for obstructions
Follow this procedure to check the ADF for obstructions. You do not need to turn off the power when clearing document jams.
Document jams in the ADF (Document Tray)

1. Press <Stop/Reset>.
   
   
2. If a multi-page document is loaded, remove any documents other than the jammed page from the ADF, then open the Feeder Cover.
   
   
   
   
   
3. Remove the jammed page from under the roller to the Feeder Cover side.
   
   
   
   
4. Pull out the jammed document from the ADF. If the document cannot be easily pulled out, proceed to section Document jams in the ADF (inner side).
   
   
   
   
5. After removing the jammed document or if a document is not jammed, check the document feed area to make sure there is no foreign material. If you find foreign material, carefully remove it.
   
6. Close the Feeder Cover.
   
   Note : If documents remain in the ADF after pressing the Stop/Reset button during scanning, "DOCUMENT IN ADF" appears on the LCD. Press the OK button so that the remaining document is automatically fed out.
   
   When rescanning the document after clearing the error, rescan it from the first page.
   
   Note: The document may not feed properly depending on the media type, or your environment, such as when the temperature and humidity are either too high or too low.
   In this case, reduce the number of document pages to approximately half of the loading capacity. Another alternative is to scan from the platen glass.
   
   

• If documents remain in the ADF after pressing <Stop/Reset> during scanning, [Document in ADF] will appear on the LCD. Press <OK> so that the remaining document is automatically fed out.
  
• When rescanning the document after clearing the error, rescan it from the first page.
  
  
  
  

Document jams in the ADF (inner side)

1. Press <Stop/Reset>.
   
   
2. If a multi-page document is loaded, remove any documents other than the jammed page from the ADF, then open the Feeder Cover.
   
   
   
   
3. Raise the paper release lever (A) then remove the jammed page from under the roller to the Feeder Cover side.
   
   
   
   
4. Open the Document Cover and pull out the document from the inner side.
   
   
   
   
5. Close the Document Cover.
   
   
6. Close the Feeder Cover.
   
   Note: When rescanning the document after clearing the error, rescan it from the first page.
   

Document jams in the ADF (Document Output Slot)
If the document is jammed in the Document Output Slot, pull it out.
Note: When rescanning the document after clearing the error, rescan it from the first page.


Trust this is helpful. Please vote. :)

Please check the sensors and actuators ,open & close front door to reset nisfeed.Clarification Top feed = Automatic Document Feeder?If YES,please verify misfeed paper beetween coverplaten and feedbelt(Yellow).Is necessary disassembly the ADF.Good luck.You will find a little paper.

If you are receiving an Error Code 103 or a Paper Jam error, but there are no pages in the ADF (Automatic Document Feeder), follow the steps below:

1. Close the scanning application (such as PaperPort)
2. Turn off the scanner and the computer
3. If you have a combination ADF with a Flatbed scanner, unplug the ADF cable from the base of the scanner
4. Plug the ADF cable back in
5. Turn on the scanner power
6. Turn on the computer
7. Try scanning again

For a Paper Jam or Error Code 103, make sure that the ADF cable in the rear is connected to the scanner base. Check the flatbed to make sure that it is clear. A page incorrectly placed on the flatbed may interfere with a page feeding through the ADF.

If your scanner stops scanning due to a paper jam in the Automatic Document Feeder (ADF), a warning dialog box appears after a few moments.

To clear a paper jam:

1. Open the Automatic Document Feeder cover.
2. Remove the jammed paper and close the cover.

If you are receiving a paper jam error, or if the scanner is running continuously, check to make sure the paper sensor arm is not stuck down.

1. Open the Automatic Document Feeder cover.
2. Look for the small black plastic arm
3. When you press on this arm, it should move freely up and down
4. If the arm is stuck down, please contact Technical Support for troubleshooting options
5. Close the ADF cover.

open up the ADF and see if there's something in the way on the side that's not pulling through

Try this link for more Printer Resources

There maybe a small piece of paper stuck within the feed path check this as it is all sensors so the machine is giving a reading that there is a jam or place a original on the feeder and press the copy button as you may of had a jam and the machine is asking for the original to pass through it again.

I suggest the first one though
Thanks J

Hi, When you had the doucment feed jam were you able to clean or remove any paper that might be blocking the paper to be scanned? It sounds like there is paper still in the document feeder , I would open the DF and check very closely to make sure no paper is in the way!Good Luck!