Problem with the date

Hi Anna the link below is to a user manual download for atomic talking watch... Have a nice day..
http://cdn.lssproducts.com/downloads/101006%20Talking%20Atomic%20Watch%20Instructions11032009.pdf

you can't do a repeat every 3 days from the iphone.

You should do it from your desktop/web calender

This Watch has no Batteries Its a manual Automatic 15 jewel watch.
It has a perpetual calendar that is set manually by turning the bottom right stemIt has day which is set from center winding stemIt has date which is set by pressing the top right press pin
The easiest way to set the calender is to match the small red numbers(year 2000 and up)to the month at the bottom using the lower right stem.The top calender should show the right day against one of three dates
Value for a good one Up to 200 dollars in original box

maybe try going into settings and make sure your settings are correct, country - date, time zone etc

To set the calender: Press the Calender/Time button. Press and hold the Time Set button for 3 seconds; the first digit of the date will start blinking. Then type in the date as two digit number for the month and date and a 4 digit number for the year. Add a zero in front of the month or day if under 10. Then press Time Set again. Press the CE/C button to return to the Calculation mode
(hold for 3 seconds)
Thus for today [Cal/Time] [Time Set] 0 9 1 5 2 0 1 0 [Time Set] [CE/C]

(hold for 3 seconds)
For December 1, 2010 [Cal/Time] [Time Set] 1 2 0 1 2 0 1 0 [Time Set] [CE/C]

To set the Time from the Calculator mode, you press the Calender/Time button twice before pressing and holding the Time Set button for 3 seconds; again the first digit of the current time will blink. Then type in the time as a 4 digit number followed by the AM/PM button to switch from AM to PM or PM to AM. Then press the Time Set button again and then the CE/C button to return to the calculator mode. You will see an A (AM) or P (PM) to the right of the time as you set it.

So for 5:06 PM you type
(hold for 3 seconds)
[Cal/Time] [Cal/Time] [Time Set] 0 5 0 6 [AM/PM] [Time Set] [CE/C]

I hope this helps. You can find the manual here: http://www.usa.canon.com/cusa/consumer/products/calculators/printing_calculators/mp11dx#BrochuresAndManuals as a pdf.

Cindy Wells
(I'm using Cal/Time for the button that has an icon that looks like a 1 month calender on the left and a clock on the left.)

this happened to me and all you have to do is go to the options, click on the calender and set it back about a year if u only set it back for 2 days the problem will most likely to come back in 2 days.
best of luck with it.

Hi,

Sounds like either you Service book [CICAL] maybe curropt; delete the service book and wireless sync the device to push new service book.

If that doesn't work; check if your colleagues have the same issue too, it may be a greater issue with the BES. i.e - One way Calender Sync issue.

Ask your IT guy to go through the BES logs to search for errors under your PIN for the day you had made entries on Calender.

Do few Tests - one from the Device and sync and the other on your desktop mail and sync.

I hope this helps, let me know how it goes,

Thanks.

if date and time is set in camera correct the info is attached to each photo-even though you don't see it if you right click properties of photo it is there-some models don't offer date and time stamp because if you tell the printer to do it it should add it on print

check the manual not sure if you have it.

look at chapter 4 setting date and time.


http://www.retrevo.com/search/v2/jsp/downloadPage.jsp?doc=f4d9a135035a5252b4b4a3e4baf8c3a6&q=Brother+1270E

http://telephones.att.com/telephones_ui/support/dsp_manual.cfm?manualID=339


Here's the official AT & T link for your manual.