At Fixya.com, our trusted experts are meticulously vetted and possess extensive experience in their respective fields. Backed by a community of knowledgeable professionals, our platform ensures that the solutions provided are thoroughly researched and validated.
Re: I have a Maytag MAH-24 that is giving me an E3 error.
E3
Cause: The water heater element does not work properly or the filter mesh is blocked. Remedy: Clean the filter mesh and if the problem continues please contact service
- If you need clarification, ask it in the comment box above.
- Better answers use proper spelling and grammar.
- Provide details, support with references or personal experience.
Tell us some more! Your answer needs to include more details to help people.You can't post answers that contain an email address.Please enter a valid email address.The email address entered is already associated to an account.Login to postPlease use English characters only.
Tip: The max point reward for answering a question is 15.
What does E3 mean on Maytag Neptune washer?"); display: inline-block; height: 24px; width: 24px; margin-top: -1px;">
What is E3 error on Maytag washer?"); display: inline-block; height: 24px; width: 24px; margin-top: -1px;">
How do I fix E3 error on my washing machine?"); display: inline-block; height: 24px; width: 24px; margin-top: -1px;">
What does E3 and F6 mean on Maytag washer?"); display: inline-block; height: 24px; width: 24px; margin-top: -1px;">
Feedback
Feb 20, 2011 - These codes in your (made-by-Samsung) Maytag washer might pop up during the ... In fact, the E3 error code means that the Machine Control wants to make the motor spin but won't do it because it's getting a weird reading from the tachometer.... MAH6700 and MAH8700 models (they use the same motor).
May 15, 2015 - Samsung uses the 3E error code to indicate a drive motor tach fault. ...If you're handy, you can fix your Samsung front load washing machine error code ....My samsung frontload washer shows e3 and the drum does not turn ...
You will have to contact Maytag and speak to their service dept and give them your model number. Ask them what a 5E eror is and when you call for service, tell the repair facility what Maytag told you. That will next to eliminate labor cost for Diagnostic.
Hi, the E3 error is comes up when the water heater element does not work properly or the filter mesh is blocked.
Remedy: Clean the filter mesh and if the problem continues, the main board needs to be replaced.
“E3” code – Machine control is attempting to drive the motor but is not seeing any tach
response. Visual Check shows motor is not moving. (Locked or Hall Sensor fault.)
Possible causes of ‘E3’ codes:
1. Spin drum stuck – Verify that the spinner moves freely to eliminate this cause.
2. Hall Sensor fails or is loose – When the Hall Sensor fails or becomes dislodged, the control
doesn't recognize that the motor is spinning and shuts down. The result will likely be an “E3”
code in the worst case, or “SUdS” if it is only getting a partial rpm reading. Check wire
harness connector(s) to motor.
Hall Sensor – PCB that is located on the back of the motor that senses motor rpm. It is not a
separate part, but rather an integral part of the motor.
i also have this problem. to get the door to unlock, just unplug the washer and it should open in a min or two. you will hear a click. you may have a mini flood but at least you can get your cloths out and bail out the water. my problem started when i began using a new detergent from Tide called total care. Still tying to get the pump to work.
Well this error code is Cause due to: Water supply switched off. Remedy: Switch off appliance. Turn on water supply. Reset the cycle. thats all to reset the error code. Post comments if further you have the same problem.......
×