Door opened when i came home but opened slowly then would not open again makes adelayed tumpping sound then doesn't do anything.

you might have hit hard to close the door. open door pad n try to open the gate

Open the dryer door and slowly rotate the dryer drum in a counterclockwise (CCW) direction. Rotate the drum 2-3 revolutions and then shut the door and see if it will start. If it continues to just hum and not start could indicate a voltage issue, motor issue or a friction issue. Open the door again and locate the door switch plunger in the upper or lower corner on the hinge side of the drum opening. Hold the plunger in while someone begins rotating the drum counterclockwise. While turning the drum counter clockwise and holding the door switch plunger inwards press the start button. If it starts, there is likely a friction problem or motor problem.
What is the model number?

make sure frige is level left to right. then make back slightly lower than front. while making sure it is level left to right.

Open the dryer door and slowly rotate the dryer drum in a counterclockwise (CCW) direction. Rotate the drum 2-3 revolutions and then shut the door and see if it will start. If it continues to just hum and not start could indicate a voltage issue, motor issue or a friction issue. Open the door again and locate the door switch plunger in the upper or lower corner on the hinge side of the drum opening. Hold the plunger in while someone begins rotating the drum counterclockwise. While turning the drum counter clockwise and holding the door switch plunger inwards press the start button. If it starts, there is likely a friction problem or motor problem.

Its probably because of how old it is mine never did that till recently. It will still work just keep a disc inside the xbox and itll be fine. And if you want to try to fix which could probably damage your xbox but i wont stop you here is a guide.http://www.youtube.com/watch?v=E3f9MZm7rQc Btw I realize that he is very akward in his video but definetly helpful. Also I did not include disassembly of xbox which you might want to do on your own if your really brave and not afraid to damge your xbox.

i got the same problem :S

Hi

Dishwashers use Bi-Metal strip to allow the dispenser to open/close. This strip when heat up causes the soap door spring to open up the dispenser. If this strip is not heated doesn't allow the door to open. The strip may not be getting 120V or maybe disconnected. Newer (plastic liner) dishwashers use a wax motor to open the soap dispenser. The plunger inside the wax motor slowly moves and pushes the plunger and door open. And, if this wax motor doesn't receive 120 volts, then it'll not work. Please check the voltage to the wax motor/Bi-metal strip; also inspect the connections to these.

Hope this helps...

Daniel

Hi. I have seen this before, although usually not from chamberlain garage door openers.

Pull the release cord that unlocks the door from the opener, and manually open the door ALL the way open.

Then lock back in place in the open position.

Then use automatic opener to shut door.

It will close very slowly, but should close all the way.

Then, open the door again using the remote, and the door will once again open slowly, this time it should open all the way.

Then close door with remote, and door should now close as it is supposed, with the proper speed.

The slow opening and shutting is the system position sensor resetting itself.

This is why your door is acting up.

I would also look up by the belt drive connects to the front of the garage door opening, to make sure there isn't any dirt, cobwebs, or other obstructions on the sensor that may cause it to re-close the way it does.

Hi

Dishwashers use Bi-Metal strip to allow the dispenser to open/close. This strip when heat up causes the soap door spring to open up the dispenser. If this strip is not heated doesn’t allow the door to open. The strip may not be getting 120V or maybe disconnected. Newer (plastic liner) Maytag dishwashers use a wax motor to open the soap dispenser. The plunger inside the wax motor slowly moves and pushes the plunger and door open. And, if this wax motor doesn’t receive 120 volts, then it’ll not work. Please check the voltage to the wax motor/Bi-metal strip, also inspect the connections to these.
Hope this helps... Please revert for any further assistance.

Daniel

The motor for the auger drive runs pretty slow (about 18 rpm), it could be the drive is running continuously (unless the door is open). Check that and let me know some more info, is the noise real loud, soft, etc. Can you feel anything vibrating or running when the door switch is pressed in?