Front Load washer won't start

he f20 (or fh) error code on a Whirlpool Front Load Washer is an indication of a water supply issue. To remove the f20 error code from the display panel, press Pause/Cancel 2 times. If that did not clear the error code, see below for what may be wrong

heres a link...https://removeandreplace.com/2016/01/12/whirlpool-washer-error-code-f20-troubleshooting-front-load-washing-machine/

Washer Not Filling:

• Door Not Closed and Locked
  • Front load washers won't fill if the door is not closed and locked. Listen for the door locking when starting a cycle, then pull on the door to make sure the door is closed and locked.
• Delayed Start Feature
  • Some washers have a delay prior to filling, where the electronic control is checking the dispenser function. This is Normal.
• Flashing Lights or Error Code on Display
  • When there is a filling issue, the washer may shut off and display one of the following codes: LF, LE, nF, IE, FH, E10 or F20.
  • If the washer is displaying one of the above error codes, then do the hard reset procedure listed below.

If the appliance is not accepting input from the control panel, follow the steps below to reset the control:

1. Unplug or turn the circuit breaker off for 30 seconds.
2. Plug the power cord into the wall outlet or turn the breaker back on and wait 30 seconds.
3. Press the Pause / Cancel / Stop button twice to clear the display.
4. Start a short cycle, to check operation of the appliance, by selecting a cycle and pressing and holding the start button until the appliance starts.

Aren't microprocessor controlled appliances wonderful? Especially when the code is flawed! No wonder the space program bit the dust!

Press the cancel button twice to cancel the error code. There should be an error code flashing -- for example 'F02'.

try holding the sop/cancel button for 15seconds, this should reset it but may not completely remedy the problem. after you reset it see if any other lights blink or if any other problems arise

hi,

This error code indicates that an unbalanced load is detected.

if the load is unbalanced, the washer will display this code while attempting to balance the load at the end of the wash cycle and before the final spin. If the code remains and the wash cycle dial is flashing after the recovery routine has stopped, open lid and redistribute the load. Close lid and press Start/Pause.


If the washer is not level, the washer may be more sensitive to unbalanced loads. The washer must be level from side to side and from front to back. The front and rear feet must be in firm contact with the floor. Make sure the locknuts are tightened.

If Power/Cancel or Pause/Cancel does not work
Unplug the washer or disconnect the power for one minute.
Plug in the washer or reconnect the power.
Re-select the cycle and press Start/Pause.

f22 is a door lock error try this hit cancel turn your dial to another setting, hit start and once it starts hit cancel again and it should unlock. thats what i did anyway.
If you're getting an F22 error, you will want to check anything to do with the door latch switch.

Answer Duet HT®

Duet®
Duet SportTM

This error code indicates that the door is not locking.
Is the washer door firmly shut?
The door must be completely closed for the washer to operate. The door may look as if it's closed, but it may not be latched. Open the door and firmly close it.
Were you washing a large load?
Before you close the washer door, check for laundry items sticking out beyond the door opening. Leave enough space in the washer to allow the clothes to freely tumble. Reduce your load size if needed.
To remove the error display, press Pause/Cancel twice.


If Pause/Cancel does not work:

1. Unplug the washer or disconnect the power for one minute.
2. Plug in the washer or reconnect the power.
3. Re-select the cycle and press Start.

NOTE: If the error remains on the display, and all of the other conditions above have been checked, call for service.

Select PAUSE/CANCEL twice to cancel the cycle. Select
DRAIN/SPIN if there is excessive water in the washer.
Re-select cycle and select HOLD TO START. If the problem
remains, call for service.

press cancel. (turns off washer)
press start/pause (wake up)
hold cancel and start/pause 10sec

last error code will come up.

E47 door lock error

check wires connections to the door lock..

replace door lock..

hope it helps