I have a Magnavox Plasma TV. Model # 50MF2310/37
It was real windy outside and the power flickered, now I al get is 4 blinking red lights and nothing else happens. Does the 4 blinking lights possibley mean a fuse is blown or something else?
Thanks
Here is the solution. For less that 100$ your Magnavox Plasma TV. Model # 50MF2310/37 will be running like a champ.
Issue:
Magnavox Plasma TV. Model # 50MF2310/37 screen has no picture.
There is no sound, TV comes on and then after a few seconds clicks and
screen remains blank.
Cause:
On the main power circuit board to Capacitors are prone to failure from
over load. The caps are 3300uf 10v 105+c capacitors located to the left
of the AC power input.
Service:
Magnavox will refer you to a service center. They will advise $$$ for
an inspection. They will also want to charge upwards of 500$ to replace
the entire board.
Solution:
1. Unplug your TV
2. Disconnect all connections from your TV
3. With assistance lay your TV on its face on a non-scratching service
4. Remove the back panel screws.
5. Lift back panel off
6. The central board is your main power board.
7. Remove all wire harnesses from the main board.
8. Remove all screws that are holding the main board in place.
9. Lift the main board out and carefully place it into a non electromagnetic pouch.
10. Take the board to a Circuit Board repair shop.
11. Have them replace the the above mentioned Caps.
12. Re-install the board in your TV.
NOTE: Replace the caps with 3300uf 16v 105+ high temp caps(preferrably Japanese caps)
This fix cost me 80$ and my time to search for other who had the same issue. Try searching for Magnavox Plasma TV. Model # 50MF2310/37 bad circuit board or Magnavox Plasma TV bad capacitors or Magnavox Plasma TV bad ciruit board.
Hope this all help, Magnavox is should take ownership for this problem
and recall any tv's that have these caps in them. The worst part about
this is that teh **** from the repair center that was paid 100$ to
check the TV, stripped out the screw holes and damaged the case for the
TV.
Portland Laptop Repair was awesome. They repaired the board and it
looked like new. Check them out at http://www.laptopportland.com/
Jeff G
Portland, OR
Here is the solution. For less that 100$ your Magnavox Plasma TV. Model # 50MF2310/37 will be running like a champ.
Issue:
Magnavox Plasma TV. Model # 50MF2310/37 screen has no picture.
There is no sound, TV comes on and then after a few seconds clicks and
screen remains blank.
Cause:
On the main power circuit board to Capacitors are prone to failure from
over load. The caps are 3300uf 10v 105+c capacitors located to the left
of the AC power input.
Service:
Magnavox will refer you to a service center. They will advise $$$ for
an inspection. They will also want to charge upwards of 500$ to replace
the entire board.
Solution:
1. Unplug your TV
2. Disconnect all connections from your TV
3. With assistance lay your TV on its face on a non-scratching service
4. Remove the back panel screws.
5. Lift back panel off
6. The central board is your main power board.
7. Remove all wire harnesses from the main board.
8. Remove all screws that are holding the main board in place.
9. Lift the main board out and carefully place it into a non electromagnetic pouch.
10. Take the board to a Circuit Board repair shop.
11. Have them replace the the above mentioned Caps.
12. Re-install the board in your TV.
NOTE: Replace the caps with 3300uf 16v 105+ high temp caps(preferrably Japanese caps)
This fix cost me 80$ and my time to search for other who had the same issue. Try searching for Magnavox Plasma TV. Model # 50MF2310/37 bad circuit board or Magnavox Plasma TV bad capacitors or Magnavox Plasma TV bad ciruit board.
Hope this all help, Magnavox is should take ownership for this problem
and recall any tv's that have these caps in them. The worst part about
this is that teh **** from the repair center that was paid 100$ to
check the TV, stripped out the screw holes and damaged the case for the
TV.
Portland Laptop Repair was awesome. They repaired the board and it
looked like new. Check them out athttp://www.laptopportland.com/
Jeff G
Portland, OR
×
Im not sure im new here. lots of people with problems, but no one seems to answer or respond to them lol. I have 5 blinking lights. what i gathered so far, it's either a fuse on the main power board, or the board itself.Juust open the tv up lots of screws, dont forget to take off the small little screws on the hdmi, and the nut on the coax.
My plasma made a loud POP! and now no pic only sound. What could that be?
Goater, is the fuses suppose to be white? Is that normal or blown?
3,488 views
Usually answered in minutes!
why is there no responses shown to this problem
I have a Magnavox 50" Plasma. mod# 50MF231D/37. 4 Red Blinking lights on power up. Called Magnavox for help. Out of Warranty. no help,bring it to repair shop near you. if there is any way to narrow it down to the power supply assy, i would like to know it.. if the tv sits for a few days, it will power up and function for a few hours, then dies, with 4 red blinking lights. HELP!
red light blinking no tv screen complete shut down
I have the same tv and the same problem...we were told to upload new information into the tv...on a disk drive...we did...it fixed it...but the next day started blinking again! Any help greatly appreciated!
Same red blinking light occured for me this morning. Anyone find an answer yet?
i have the same tv 50mf231d/37 and today i got up and tried to turn it on the normal green light turned on but the tv itself didnt do anything and within 15 sec the green light turns red and it flashes 3 times stops for a sec and again 3 times it continues doing that but it doesnt turn on i did have the power go out on me a couple times before this happened so i dont know if that had something to do with it and is it something i can fix or am i screwed
I have a magnavox 50 in plasma (50MF231D/37) and everytime I turn it on it takes 1 minute for the picture to come up. Sometimes it never comes up and it turns off by itself and thats when the blinking red light turns on. I just end up pushing the reset switch on my surge protector and wait 10 seconds until I switch it back. This usually works but I still have to wait a minute for the picture to show up.
I have the same problem. After a power surge the tv turns on then immediatly shuts off and blinks 6 red lights. Can anyone tell me where to find the meaning to the blinking lights code. It has to mean something.
×