The power button is blinking alternately an error message comes out saying the ink counter needs to be reset.can you help me have the resetter? Where can I find it?

How to reset Canon Pixma iP2770/iP2772 error 5B00, follow instruction bellow;
1. Turn off printer
2. Press and hold RESET button
3. Press and hold POWER button.
4. Released RESET button, POWER still pressed
5. Press and released RESET button 5 times
6. Released POWER button
Now, printer on SERVICE MODE condition. In this condition, computer detect found new hardware.
7. When computer detect FOUND NEW HARDWARE, wait about 20 seconds and press CANCEL
8. Open software resetter Canon Pixma iP2770/iP2772 - download Re-setter Canon Pixma iP2770/iP2772
9. Set Destination - Region : select region - SET - OK
10. Load paper = 1 sheet
11. Clear Ink Counter - SET - OK
Wait, the printer will print D=000.0
12. Ink Absorber Counter - SET - OK
13. Reset iP2770/iP2772 is done, now turn off printer.
14. Turn on printer and try to print
Have problems when use software re-setter, read this Problems When Reset Canon Printer
15. When try to print, show up error message "The following ink may have run out",press and hold RESET button 7 seconds, then released them

The waste ink counter is full, you need to reset it.


First, inbox me and i will send you the reset software, otherwise you pay. its canon service mode tools v2000

Step 1: enter in service mode in order to used the resetter:

• Turn off the printer without pulling the power cords.
• Hold down Resume button and press Power button.
• Keep holding down Power button and let Resume button go.
• Then Press Resume button 5 times then let both buttons go.
• The Alternate Blinking error is gone: the printer is in Service Mode state.

Get your printer's service manual to help you in future:
http://www.gondack.com.ar/media/useruploads/files/ip4700-ssm.pdf


Good Luck!

First Step : Set The Canon PIXMA MP287 To Service Mode. To do that, follow this step, it's so easy.

1. Turn off the printer without pulling the power cord.
2. Press and hold the RESUME button (Green button), keep holding it and then press the power button, do not let go yet.
3. Keep holding the power button, now release the RESUME button and then press theRESUME button for 5 times and quickly release the POWER button.
4. When the printer entered the Service Mode, all LED will stop blinking.

Second STEP : Reset Canon PIMA MP287 Using Resetter. Open the mp287.exe, and then follow this step.

1. Insert some A4 paper, the printer will print the result.
2. Look for "Clear Ink Counter" section, press the "Main" button and wait for the message "A function was finished" and then press "OK" button.
3. Press the "Platen" button located beside the "Main" button.
4. Look for "Print" section, press the "EEPROM' button, select "Rear Tray" and pres "OK" button.
5. The printer should printout the result. That's all, you may turn off your printer now. Sometime you need to press the POWER button several time in order to turn off the printer.

source:http://stepblogger.com/tutorial/tutorial-how-to-reset-canon-pixma-mp287-using-resetter-tool/

The waste ink counter is full, you need to reset it.


First, download the resetter PCM_servicetool (.rar)

Step 1: enter in service mode in order to use the resetter:

• Turn off the printer without pulling out the power cord.
• Hold down Resume button and press Power button.
• Keep holding down the Power button and let Resume button go.
• Then Press Resume button 5 times then let both buttons go.
• The Alternate Blinking error is gone: the printer is in Service Mode state.

Step 2:

• Extract the resetter and double click "servicetool.exe"
• Click Reload Button and you will get a new USB port.
• Load some papers in your printer and press the "Main" Button, wait until it shows "error 001" then press OK.
• Then press "EEPROM" button and the printer will print some text, after that click OK
• Then power off the printer (sometimes you have to press twice the power button to turn off) and turn on again.
• That's done.

This is the error code printer Canon IP1200, IP1300, etc. light blink Indicator:
3x orange 1x Green = mechanical error
if you dont have any knowlegde about printers, better bring your printer to Canon service center.
4x orange 1x green = printer absorber full
reset your printer using software ressetter or try using manual reset. different printers have different manual reset.
5x orange 1x green = black cartridge/color cartridge error
can be chip error or connector is dirty.
7x orange 1x green = black cartridge/color cartridge error
can be chip error or connector is dirty.
8x orange 1x green = printer absorber full
reset your printer using software ressetter or try using manual reset. different printers have different manual reset.
12x - 17x orange 1x green = cartridge detection error

How to Reset waste ink counter Manually 1. Unplug power and USB cable. 2. Open door and hold power button. 3. Connect power. 4. Close door, then release power button.

How to Reset waste ink counter using Resetter
1. Download software for Canon iP1200 printer. DOWNLOAD 2. Unzip downloaded file to any location using, 7ZIp, WinRAR, Winzip, etc 3. Run GeneralTool.exe 4. select connected USB port number from USB port 5. Click LOCK RELEASE, and select the applicable model name in SET DESTINATION 6. In CLEAR WASTE INK COUNTER, select MAIN or PLATEN. the selected waste ink counter will be reset.
Thank you for posting. Hope this helps.

How to Reset printer canon ip2770 (E 5B00) IP2770 Resetter v1074 I have tried. IP2770 Resetter was sent by our friends in Jambi, and hopefully this iP2770 Resetter runs perfectly. Resetter is free passwords ... and FREE
How to Reset Canon IP2770 Error 5B00
Download Canon iP2770 Restter v1074 free pass Here
(Do not forget to turn off the download manager, for a successful download)
Go to the iP2770 Service Mode:
1. The printer is turned off and plugged the power cord.
2. Press Resume button 2 seconds
then press the POWER button until the green light on (when pressing the POWER button, Resume button ... jgn released first)
3. Then release the RESUME button, but do not release the POWER button.
4. While the POWER button is still depressed, press the Resume button 5 times. Led will light turns green orange with the last glow orange. (Do not be mistaken 4x because the printer will die completely, but it is temporary too) Then ...
5. Release both buttons simultaneously.
6. Led will blink briefly and then will glow GREEN.
V1074 iP2770 Resetter Then run it:
1. Prepare 2 blank paper in the printer
2. In the menu "Clear Ink Counter" click "Play" and "Platen"
3. Click Test Print ... Done ...
(In some experiments sometimes "platen" unable / err message appears, but no problem, still can work well)
Hopefully Successfully

Procedure to reset Printer canon MP145 and Canon MP160 with Error Code Message for Printer Canon MP145 and Canon MP160, you can find error code message the end of this post:
1) With the printer powered off but connected to a power source, press the Power button while pressing and holding the Stop/ Reset button.
2) When the Power is lit, press the Stop/Reset button two times while pressing and holding the Power button.
3) When releasing the Power button and the Stop / Reset button (regardless of order), the printer will move into a service mode. (Waiting for menu selection)
4) When the on/off lights in green, press the Stop/Reset button the specified number of time(s) according to the function listed in the table below.(Each time the Stop/Reset button is pressed, the LED lights alternately in orange and green, starting with orange.)note: press 4 times for waste ink counter reset.
The number of the Reset
button pressing
LED Function Remarks
0 time Green Power off
1 time Orange Service pattern print
2 times Green EEPROM print
3 times Orange EEPROM reset
4 times Green Waste ink counter reset
5) Unplug cable power. (for MP145 / MP150)
6) Turn Off Power. (for MP160)