Euroart dishwasher error message

All questions need 'make model (what it is)' and you only have 1/3.

E3 is water too high or too low, or hot water related not hot enough or vibration depending on maker.

Error message E3 in integrated compact dishwasher indicates too much inlet water and/or a leak.
Oct 7, 2019

Compact dishwasher displays error message E3 - Electrolux

The E24 error code on a Kenmore dishwasher model 630.1390 typically indicates a problem with the drain pump or the drain hose. This can cause the dishwasher to start adding water but then shut off and display the E24 error message.
Here are some steps you can try to fix the issue:

1. Check the drain hose for any clogs or blockages. Make sure the hose is not kinked or bent and that it is properly connected to the garbage disposal or drain.
2. Inspect the drain pump for any debris or foreign objects. Clean out the pump, if necessary.
3. Check the air gap on the dishwasher. Make sure it is not clogged or blocked.
4. Inspect the control board and check for any error messages.
5. Power off the dishwasher and unplug it for 10 minutes to reset the electronic control board.
6. Make sure the dishwasher is level and that the legs are adjusted properly.

If the problem persists even after trying these steps, it might be best to contact a professional technician for further diagnosis and repair.

Good Morning steven hutchings, thanks for your inquiry!

I understand that your Electrolux dishwasher is displaying an error code 03. Normally, error code 03 means an issue with the wash motor, wash motor hall sensor, or control panel. I would suggest performing a reset on your dishwasher that could help clear any false error codes. You can reset your dishwasher by flipping the household circuit breaker in the off position for ten minutes. If you continue to have an issue with your dishwasher displaying an error code 03, I would recommend having a professional technician come out and properly diagnosis your dishwasher. This will help to avoid any unnecessary part purchases. Hope this is helpful. -Matt

Go to manufacturers website with complete model #. You should be able to find parts list there.

This sounds like your motor is not circulating properly, this will cause the spray arms not to operate properly, or at all. Are you receiving any kind of error code on the display? Also, how far is the dishwasher filling up?

Hello,

Some models of Frigidaire washers come with a digital readout display that informs the operator of the unit's function and any errors.

Error codes indicate that a problem has occurred and should be addressed. Different models of Frigidaire washers may vary in their fault displays.

Some washer models use flashing lights at the unit's start, door lock, wash, rinse, final spin and control indicators to display error codes.

Hope this help?

Thanks.

I have just had the same issue, error 3. Were you able to find a fix?

Hi,

Don't know Euroart. However I would bet it is a Chinese manufactured product with European aspirations.

Anyhow, if the machine keeps filling up there could be a problem with either your inlet valve/solenoide. Sometimes the solenoide sticks and does not shut the water off.

Or alternatively your pressure switch or pressure hose has a problem. If the pressure hose has come loose then the pressure switch does not detect water level.

Hope this helps.

Regards
Ash

yes a heater problem can definitely be your issue. i dont have access to euroart information to help you properly diagnose whats wrong but you should have water in the dishwasher so hot it steams. if it doesnt steam then you might have a bad (element, heat assy, or control board.) sometimes its even a broken wire

Simple fix for me
Simply look at right side of machine get a flash light pull the insulation away from machine stick the light in look for the white little resovoir and the styrofoam float switch.
syphon the 1/2 cup collection this allows the float in the attached
cup to drop kicking the sensor out....
I dont suggest disconnection the sensor as im sure it will come back to haunt you. =)

worked for me takes 5 minutes
enjoy