Need wiring diagram ,lost the instructions manual

Question edited for clarity.
Question moved to RVs.

Check out the link

https://www.google.com/search?q=94+thor+pinnacle+motorhome+fuse+box+diagram

..

Thor never made that model so they will not have that information available. Thor bought Damon around 2011-12 time frame. Many places that fix RV's will tell you that if you bought a Damon product before Thor bought them, it is probably still in good condition and has needed minimal fixing but anything after Thor, forget it. At least when you throw your money in the toilet you know why you lost it.

I did find some available 2000 damon challenger motorhome wiring diagram Google Search

Get a shop manual. If you're putting in a trailer harnes, try a uhaul center. They do it all the time and much cheaper than the dealer.

Thor Motor Coach - Owner Resources Put in your vin and a PDF form will give you a wire diagram pluming and others you need. I use it a lot work on my RV. I had the same problem on mine, it was a safety switch

First, the GFI runs on house current aka shore power. Make sure you are plugged in! Most GFIs have a light showing power on.

Check your breaker - not a car type fuse - in the fuse panel. GFIs are nothing but a quick-disconnect in case of a short. (Quick description)

You really need a wiring diagram for this. Try and get one online or from the mfg.

Start by tracing back towards power source from GFI. Remove GFI and check for power on the wires. Be careful, it's 120vac house current. If you have power, replace the GFI. If no power, look at the diagram and proceed to the next outlet/GFI on the same circuit. You might have to go all the way to the power distribution panel. Sooner or later you will find the open wire. Might be nothing more than a screw vibrated loose disconnecting the power feed.

Mfg typically do not have diagrams of electrical and plumbing as stated on another post.

Wiring diagrams are not available as the manufactures to not publish them. On the back of the stereo system there will be a basic diagram that may be of assistance.

I need an instruction manual for THOR elite TWD1000 Washer / Dryer.
Satch

Hi.
The Echowell Beta-2 setup manual is here:
http://www.echowell.com.tw/images/product/Beta_Set_en.pdf

--
Thor-Henrik

I have this alarm / remote start / keyless entry system and I have the poorly translated installation manual. Everything in mine installed fine in my 2005 suzuki aerio (except the power locks as the manual is worthless in that area) but I have heard nothing but horror stories from others online since I installed it.

I don't recommend you install it but if you really are determined, here is what the manual says (or tried to say and I spent 4 hrs interpretting / correcting it:

8 wire harness:
-- The 4 wire connector connects to the 4 wires harness part of the 3 relays
-- The yellow connects to the yellow of the breaker relay yellow
-- yellow w/black stripe connects to the oil sensor on the motor (look for single wire connected to sensor and generally a heat shield wrap/weave, mine was blue)
-- orange connects to the brake switch on the brake pedal
-- the blue connects to the door switch /dome light trigger

12 wire harness:
-- 6 central locking wires orange, yellow, and white plus the same 3 with black stripe.. Unfortunately the manual is not clear as to where they connect. The next page of the manual shows diagrams but they mysteriously add a white stripe to all the colors and the white wires apparently become green. I suspect that orange is not likely used in most installations and for positive door lock types (the most popular), yellow goes to unlock and yellow w/ black stripe goes to lock signal and the 2 whites go to 12v+. This is only a guess so don't hold me to it.
-- black is grounded to frame
-- Red is 12v+
-- red w/ black stripe goes to power trunk release (if equipped)
-- The 2 browns go to the left and right turn signals
-- The pink goes to the alarm

Ignition switch connections
----------------------------------------
The breaker relay:
-- blue goes to the ACC ON wire
-- Cut the ignition wire and connect the 2 greens to each end
-- Yellow connects to the yellow of the 8 wire harness

The 3 relays:
-- 4 wire harness connects to the 4 wire connector of the 8 wire harness
-- the 3 reds connects to the 12v+ red of the ignition switch (or thru the firewall to the battery)
-- black connects to the ignition on the downstream side of the 2 greens of the breaker relay
-- white connects to ACC ON
-- blue connects to the starter