Question about Euro-Pro EP1005 Iron

7 Answers

Iron heats up but the water doesn't - Euro-Pro EP1005 Iron

Posted by on

  • 4 more comments 
  • laverneray Nov 16, 2009

    My euro pro ironing solutions will not heat up water for steam but the iron does heat up. What can the problem Thanks

  • laverneray Nov 19, 2009

    Micheal I did the water and vingar it still won't heat up. Do I have to take that part apart that goes to the sionold??? One the botton of the water tank the first set of wires the plastic clip was burn bably so I took it off. Those wires are attached to a little white sqaure. And the light does not come on when the steam button in. Thanks Laverne

  • laverneray Nov 20, 2009

    I have tryed all those things and still no heat to water tank. The light does not work on the steam button .Could something be out in the heating paet and can I get parts for this??? I love the iron soulations but really need steam for what I use it for. Also I said on the bottom of the tank there was a plastic cover on the wire burnt. There are two wires going to a little white square thing. Thanks Laverne

  • laverneray Nov 22, 2009

    I know what it is now. It is the little white box like thing on botton of water tank that has 2 white wires running to it. Where can I get one to replace this one and what is it. Thanks Laverne

  • laverneray Nov 27, 2009

    Could that part be a fuse??? It is located on the bottom of the tank which holds the water, it has two white wires going to it. Ir is about 5/8 in long and 1/2 wide and is made of ceramic. Thanks I cannot locate one. Tryed that number you give and cannot get through and tryed electric supply place. Laverne

  • laverneray Nov 29, 2009

    It is not the iron itself it is the tank that you put water in on the eruo pro ironing soluation. It is inside the ironing board. it is a cermic thing on bottom of tank that has two white wires going to it. it is a fuse I think but don't know I just one to get that cermic thing to put back on it is bad.

×

Ad

7 Answers

  • Level 3:

    An expert who has achieved level 3 by getting 1000 points

    Superstar:

    An expert that got 20 achievements.

    All-Star:

    An expert that got 10 achievements.

    MVP:

    An expert that got 5 achievements.

  • Euro-Pro Master
  • 18,110 Answers

This unit has two heaters in it. One is for the water and the other is for the iron. There is either a thermal cutoff fuse or a bad heater element in the steamer section. The availability of parts and service is not good. I would get another one or a different one.

Posted on Nov 30, 2009

Ad

  • Level 3:

    An expert who has achieved level 3 by getting 1000 points

    All-Star:

    An expert that got 10 achievements.

    MVP:

    An expert that got 5 achievements.

    Vice President:

    An expert whose answer got voted for 100 times.

  • Master
  • 488 Answers

The water aperture inside the iron is clogged and no water is entering the steam chamber. You may find that a mixture of caustic soda and warm water will clear the aperture or you can try any of the proprietary iron cleaners. The aperture becomes clogged with calcium and other impurities and attempting to clean out the aperture usually fails but this is cheaper then replacing the iron so give it a go.. It may also be that the heating element is not reaching a high enough temperature to vaporise the water into steam so check that the iron is getting hot enough BUT DON'T TOUCH IT, Flick water onto the sole plate when the iron is upto temp, if it slowly boils away then it aint hot enough, it should splatter into steam..

Posted on Nov 28, 2009

Ad

  • Level 3:

    An expert who has achieved level 3 by getting 1000 points

    All-Star:

    An expert that got 10 achievements.

    MVP:

    An expert that got 5 achievements.

    President:

    An expert whose answer got voted for 500 times.

  • Master
  • 1,615 Answers

Internal there is a heating element that can burn out. Its kinda the same as you have in a dryer when it decides not to heat. You can check it for resistance if you can access it. Then you can order the part. If it has no resistance like no number then its bad

Posted on Nov 22, 2009

  • Level 2:

    An expert who has achieved level 2 by getting 100 points

    All-Star:

    An expert that got 10 achievements.

    MVP:

    An expert that got 5 achievements.

    Vice President:

    An expert whose answer got voted for 100 times.

  • Expert
  • 358 Answers

Hello Laverneray, I would like you to know how your iron works first. The way your Iron is built is as simple as this: When you put on your Iron, without activating or turning-on the steam tab, only the heating element inside the iron works, which is being controlled by a bi-metallic strip, and allows you to iron your clothes that do not require steam, Now, when you activate the steam tab, a small, white, heating box at the base of the Iron is being supplied an electric current, and it becomes hot. The heat generated by this box gets the water inside the Iron very hot, and as soon as you keep pressing your clothes after this, Hot water in steam form or aerosols, spray on your clothes, making it easier to Iron tough clothes. If the voltage now becomes really high more than the specified amount, or there is any other voltage fluctuation, this small heating box might get damaged, and this is exactly what I suspect happened to your Steam Iron. In this case, There are three options that I would tell you: 1. Try to get a very good electrician to remove this box for you, open it up, and see if it is something that can be fixed. If yes, then just tell him to fix it for you, you might need to pay a little for his services. 2. If he says it cant be fixed, then ask him whether you can get an Iron of the same type, or that uses the same mechanism, but a fairly-used one, which still has its heating box functional/working properly, then tell him to remove it and fix it for you. 3. Go to an electric store, preferably where you initially bought the Iron from, and ask them if you can get a spare part of the Iron itself, if they say yes, then just buy it from them, and let them, or a very good electrician fix it for you. Let me know how it goes / Keep me posted about the problem. Hope this helps you out. Good luck.

Posted on Nov 22, 2009

  • Level 3:

    An expert who has achieved level 3 by getting 1000 points

    Superstar:

    An expert that got 20 achievements.

    All-Star:

    An expert that got 10 achievements.

    MVP:

    An expert that got 5 achievements.

  • Master
  • 3,741 Answers

there is a heating element and a heater in the iron.the heating element is for iron heating and heater to heat the water and get stem.in your iron the heater is got faulty and not working.as you mentioned two wires .yes there are two wires.one goes for heater and other for heating element.may be its possible that heater wire is got short in between or got cut in between.so it needs to be checked and replaced after confirming either is wire or the heater itself that is faulty.you will have to check out this with multi merer.
if you are not familiar with doing this you can get it done by local repair technician familiar with this model .
-----------
This will help. Thanks please keep updated.please do rate the solution positively .thank you for using fixya.

Posted on Nov 20, 2009

  • charlymonty Nov 22, 2009

    after extensive searching, it's the only one I could find, so I suggest you get two while the getting is good!Customer Support for Sharkvac Products - sharkvac.com
    This link will take you to a web page that will allow you to send the manufacturer an email explaining the part you need. Please, before you send the email, try your best to find your manual and see if there is a part number listed for the part you want. If not, and the old part is available (like—if you have a broken one), check it over thoroughly (perhaps using a small flashlight and magnifying glass to make sure you don't miss it) for any numbers that might be stamped, embossed, or etched into it. Even if they are not part numbers, they may help the manufacturer to locate the one you need. No matter what, send them as much information as you possibly can in order to help them be able to help you—the easier you make it on them, the more likely you are to get satisfactory results. Finally, here is a toll-free number for the manufacturer's tech-support line: the same "homework" applies before you call it:1-800-798-7398. Hours are Monday through Saturday from 9:00am to 6:00pm Eastern Standard Time.
    I hope this helps!


    to see the list of parts available just click on the link directly

    http://www.sharkclean.com/cgi-bin/livew/...

    This will help. Thanks please keep updated.please do rate the solution positively .thank you for using fixya.


  • charlymonty Nov 28, 2009

    click on this link directly

    if the part which you are mentioning looks like this then its fuse

    http://media.digikey.com/photos/Littelfu...

    other wise its not fuse its something else.

    thanks.keep updated.

×

  • Level 3:

    An expert who has achieved level 3 by getting 1000 points

    Superstar:

    An expert that got 20 achievements.

    All-Star:

    An expert that got 10 achievements.

    MVP:

    An expert that got 5 achievements.

  • Master
  • 10,865 Answers

Hello. i can assist you. It appears that your iron is heating up but you are not seeing any steam generated. There are a few possible causes for this: 1. On/Off button is not in the “ON” position.2.Steam generator has no more water.3.Unit is not plugged in.4.Steam is not visible because the temperature of the soleplate is at maximum and room temperature is high.5.Generator is not fully heated.
And here are some solutions for you to consider: 1.Press the On/Off button to the “ON” position.2.Fill with water as per instructions.3.Make sure that the On/Off button is in the “OFF” position and plug the unit into an electrical outlet.4/5. The heating time for the generator is approximately 9 minutes. Watch for the steam ready light to go off indicating that steam is ready. Regards, Joe

Posted on Nov 20, 2009

Check the solenoid steam valve which is fitted on the steam tank output pipe, there is most likely a small port where some particles have clogged it up. Fill the reservoir with vinegar and water (50-50) and allow it to soak for 24 hours, then reheat and shake vigorously to drain. After you do that, rinse it out and retry

Posted on Nov 18, 2009

2 Suggested Answers

6ya6ya

6ya staff

  • 2 Answers

SOURCE:

Hi there,
Save hours of searching online or wasting money on unnecessary repairs by talking to a 6YA Expert who can help you resolve this issue over the phone in a minute or two.

Best thing about this new service is that you are never placed on hold and get to talk to real repairmen in the US.

Here's a link to this great service

Good luck!

Posted on Jan 02, 2017

heatman101

D. Floyd Kolb

  • 43501 Answers

SOURCE: f2000 iron won't heat up

Hi,

Here is a tip that will help you to troubleshoot your iron and figure out what is wrong with it.

Electric Iron not Heating Up or not Working Right
https://www.fixya.com/support/r5300202-electric_iron_not_heating_up_or_not

heatman101

Posted on Jul 14, 2010

Add Your Answer

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

1 Answer

My rowenta Dw9280 steam iron won,t heat up.


Failure of heating element, control, or both

Mar 14, 2018 | Rowenta Irons

1 Answer

My Hamilton Beach duration iron produces steam but the burst steam feature doesn’t work


put a solution of 10% vinegar in it and try to flush the system out.... probably that circuit, which pushes a shot of water into the heating coils, is plugged.... if REALLY plugged, you may be looking for a new iron since passage of water with the vinegar is necessary to dissolve the clog to a great degree...

Nov 19, 2017 | Hamilton Beach Irons

1 Answer

It is my first time using it, I brought it from USA and it is not working at all!!


follow this steps and fix it. God bless you
If the iron doesn't heat, make sure power is on to the outlet, check the electric cord and check the thermostat .
If the iron heats but steams improperly, inspect the soleplate and clean the vents (see below) and flush sediment out of the steam chamber (see below).
If the iron produces too much or too little heat, test the electrical cord . Also test and, if needed, adjust calibration of the thermostat

If the iron does not spray properly, inspect and clean the nozzle
If the iron leaks or spits, clean the steam vents, nozzle, and tank.
If the iron sticks to fabric, clean or repair the soleplate. If the iron stains fabric, clean the soleplate, clean the tank with a commercial cleaner, and use distilled or filtered water.

Jun 11, 2013 | Black & Decker Irons

1 Answer

No steam is coming out i think it needs cleaning


Some irons like Rowenta have a self cleaning feature. If yours doesn't make a solution of 1/2 vinegar and 1/2 water and put it in your iron. Plug it in and allow it to heat that up. keep working your instant steam button for a while. Hopefully the vinegar will help remove the calcium build up and let it work.

Nov 11, 2012 | Irons

1 Answer

Bosch TDS 1445/05 Sensixx station doesn't making steam


HI!
I HAVE AN Bosch TDS 1445/05 Sensixx AND THE IRON PLADE NOT WORM AT ALL. I CHECK THE POWER.I CHANGE THE THERMOSTAT/THE CONDENSER WITH THE LAMP/.BUT STILL NOT WORK. THE BOILER WORK GOOD.PLEASE HELP ME.WHAT CAN I DO MORE. THANK YOU

Oct 06, 2012 | Irons

1 Answer

Smartex iron wll not heat up...Help!


see this causes and fix it. God bless you
If the iron doesn't heat, make sure power is on to the outlet, check the electrical cord, and check the thermostat (see the Appliance Controls Fix-It Guide) and replace if necessary

Oct 01, 2012 | Irons

1 Answer

Troubleshooting of flat iron for clothes


follow the steps and use the common sense. God bless you
If the iron doesn't heat, make sure power is on to the outlet, check the electrical cord, and check the thermostat (see the Appliance Controls Fix-It Guide) and replace if necessary.
If the iron heats but steams improperly, inspect the soleplate and clean the vents (see below) and flush sediment out of the steam chamber (see below).
If the iron produces too much or too little heat, test the electrical cord . Also test and, if needed, adjust calibration of the thermostat (see the Appliance Controls Fix-It Guide).
If the iron does not spray properly, inspect and clean the nozzle (see below).
If the iron leaks or spits, clean the steam vents, nozzle, and tank.
If the iron sticks to fabric, clean or repair the soleplate. If the iron stains fabric, clean the soleplate, clean the tank with a commercial cleaner, and use distilled or filtered water.


9_21_2012_5_20_17_am.jpg

Sep 20, 2012 | Irons

1 Answer

Rival IR600 Iron Does not turn on, not heating or lights on ?


see this causes, and use the common sense.God bless you
f the iron doesn't heat, make sure power is on to the outlet, check the electrical cord, and check the thermostat (see the Appliance Controls Fix-It Guide) and replace if necessary.
9_20_2012_11_58_53_am.jpg

Sep 19, 2012 | Rival IR600 Iron

1 Answer

Its not heating and steam doesn´t come out? where can i fixed or get parts?


Do you have limescale in your water? If so, the iron could be clogged with what looks like sand. Try bashing it around a bit and see if sand comes out the sides. If so, continue until no more sand comes out.

Apr 21, 2010 | Conair GS11 Iron

1 Answer

F2000 iron won't heat up


Hi,

Here is a tip that will help you to troubleshoot your iron and figure out what is wrong with it.

Electric Iron not Heating Up or not Working Right
https://www.fixya.com/support/r5300202-electric_iron_not_heating_up_or_not

heatman101

Apr 10, 2009 | Black & Decker D2030 Iron

Not finding what you are looking for?
Euro-Pro EP1005 Iron Logo

Related Topics:

174 people viewed this question

Ask a Question

Usually answered in minutes!

Top Euro-Pro Irons Experts

Brad Brown

Level 3 Expert

18110 Answers

Bruce Showalter

Level 2 Expert

133 Answers

Sheldon Dedek

Level 3 Expert

909 Answers

Are you an Euro-Pro Iron Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...