Pump stall press resume I did this and it came back with same message regards edward

Hi,

Follow the steps below to resolve the issue.

1 - press resume button and then press power button
2 - realese the resume button and press 2 more times then realese both
3 - press and release resume 4 times and power 2 times...

Regards,
Shawn.

i get this message on my printer
carriage stall clear carriage obstraction

i change the prints head and the colours catrage and still have the same message
can u help me

Hi there

1. With the printer plugged in and powered off, press and hold the Resume/Cancel button, then press and hold the Power button. (DO NOT release the buttons. The LED light should be green to indicate that a function is selectable.).
2. While holding the Power button, release the Resume/Cancel button. (DO NOT release the Power button.).
3. While holding the Power button, press the Resume/Cancel button 2 times, and then release both the Power and Resume/Cancel buttons. (Each time the Resume/Cancel button is pressed, the LED lights alternately in orange and green, starting with orange.).
4. When the LED light is green, press the Resume/Cancel button 4 times. (Each time the Resume/Cancel button is pressed, the LED lights alternately in orange and green, starting with orange.).
5. Press the Power button. The LED lights in green, and the reset is performed. (When the operation completes, the printer returns to the menu selection mode automatically.).
6. Press the power button to exit service mode.
Note: if you accidentally press the Resume/Cancel button more than 4 times in step 4 then just press the Resume/Cancel button at least 10 times and the printer will be returned to step 4 automatically
Please all I ask is call back and just gave a vote, it will gave me some satisfaction to know am helping some one, so I will keep on helping.
All The Best: Pineworks

Hi there you can try.
Following step by step resetting canon Pixma iP90 :

• Before resetting printer canon iP90, start with printer power off.
• Press resume button coincide with power button.
• While pressing power button, release resume button.
• Press resume button 2 times and then release both button
• Green LED indicator will blinking and then stopped blinking.
• When the Power LED lights in green, press resume button 4 times.
• Press power button and the printer power will off. Otherwise off, depress again power button.
• And the turn on the printer again, your printer canon iP90 should be response as normal.

All I ask is please come back and just gave a vote, it will gave me some satisfaction to know am helping some one so I will keep on helping.
All The Best: Pineworks

Check the printer again to see if a very small jam is present. If totally clear, press the Resume button. If same result, power the printer Off / On.

Hi,
Check your cartridges are good, must be sat correctly.

check that the timing strip is in the center

1. clean **** strip film
2. clean **** strip film sensor
It is located at the back of head carriage, use a contact cleaner.

check something is not blocking the carriage.( usual suspect )


To reset
1. Turn off printer
2. Hold down Resume button and press Power button.
3. Keep holding down Power button and let Resume button go.
4. Press Resume button 2 times then let BOTH buttons go.
5. Green lights will flash and then stop blinking.
6. When green lights are solid, press the Resume button 4 times.
7. Press the Power button and the printer should turn off, if not,
press the Power button once more.
8. Your printer should respond as normal..
Or, press reset( or resume) button 4 times then power.

Hope this helps
Regards
Richard.

See http://fixyourownprinter.com/forums/inkjet/42029
"Carriage Stall or Jam" by Stephen
Clean encoder strip with clean water, clean rod with denatured alchol you can get at Home Depot and lube with Synthetic Lubricant that you can purchase at a gun shop for about $4.

Dear caucoin,
This message appears when waste ink absorber capacity rise to about more than 95 %. To fix this problem you need reset waste ink counter and it strongly recommended that you replace waste ink absorber (integrated in print base unit). Due to complicated disassembly process i suggest you to take the printer to nearest service center. For emergency reason you may perform below procedure to reset waste ink counter:

• Plug in power cable
• Press POWER button while holding down RESUME/CANCEL button then release RESUME/CANCEL button (do not release POWER button)
• Press RESUME/CANCEL button two times while holding down POWER button then release all button (printer entering service mode and light stand by in green).
• In stand by condition, press RESUME/CANCEL button 4 times (light will flash alternately in orange & green each time the button pressed).
• Turn off printer and turn on again.

Now your printer back to normal condition. Hope this will be useful for you and don't forget to rate me.
Regards,

Source:
Canon Inkjet Forum

This is just a worthless error message. You can just reset the waste ink counter to fix this issue.. The reset instructions are given below..
1. Turn off printer
2. Hold down Resume button and press Power button.
3. Keep holding down Power button and let Resume button go.
4. Press Resume button 2 times then let BOTH buttons go.
5. Green lights will flash and then stop blinking.
6. When green lights are solid, press the Resume button 4 times.
7. Press the Power button and the printer should turn off, if not, press the Power button once more.
8. Your printer should respond as normal.

Let me know how it turned up..

Regards,
Eagle338(Sai)

Hi,

Could it be that the message is "Waste Ink is Full"?

If yes:
1: Remove Cartridge
2: Unplug the AC Power Cord
3: Hold down the RESUME button
4: Release RESUME after plugging in the AC Power cord.
5: Press the RESUME once within 5 seconds and release the RESUME .
6: Press and HOLD RESUME for two seconds or more and release it.
7: Press and HOLD RESUME for two seconds or more and release it.
8: Unplug AC Power Cord to set data.
This procedure is also available with other Canon printers here, here, here and here.

Hope this be of initial help/idea. Pls post back how things turned up or should you need additional information.

Good luck and kind regards.

Thank you for using FixYa.