Question about Toro Blowers Rake and Vac - Electric Blower/Vac - 51573

2 Answers

Toro 521 snowblower..nn replace gas line to carb, it runs inside the engine cover..removed all bolts but the back cover doesnt seem williing to be removed

Posted by on

Ad

2 Answers

  • Level 1:

    An expert who has achieved level 1.

    New Friend:

    An expert that has 1 follower.

    Mayor:

    An expert whose answer got voted for 2 times.

  • Contributor
  • 1 Answer

Or, you can try the easy approach. Take a 1/4" bolt about 2" long and cutoff the head. Force the bolt into the old fuel line on the fuel tank side (after removing fuel tank), push other end into new fuel line, tape the lines together well with electrical tape. Gently pull from one side and push from the other until new section of line comes through. Just did this and it too all of 5 minutes.

Posted on Dec 31, 2009

Ad
  • Level 1:

    An expert who has achieved level 1.

    New Friend:

    An expert that has 1 follower.

    Corporal:

    An expert that has over 10 points.

    Mayor:

    An expert whose answer got voted for 2 times.

  • Contributor
  • 9 Answers

Or you can freeze the gas line in the freezer until it becomes hard and frozen. Then lubricate it with petroleum jelly and slide it through the engine until it comes out by the gas tank.

Posted on Feb 16, 2013

  • Paul Hummel Feb 16, 2013

    Or you can freeze the gas line in the freezer until it becomes hard and frozen. Then lubricate it with petroleum jelly and slide it through the engine until it comes out by the gas tank.

  • Paul Hummel Dec 06, 2013

    I found an easier way as I had to replace the gas line again. Cut a wire hanger in two places near the hook on the hanger. Straighten the hanger and run it through the old gas line. Run the new hose behind the old line until there is no space between the hoses. Bend the back end of the hanger so it is snug on the right side of the new hose so the hanger doesn't slip through the hoses. Spray WD 40 on the old and new hose. Then take a pair of pliers and pull the hanger from the carburetor side until both hoses come through.

×

Ad

1 Suggested Answer

6ya6ya

6ya staff

  • 2 Answers

SOURCE:

Hi there,
Save hours of searching online or wasting money on unnecessary repairs by talking to a 6YA Expert who can help you resolve this issue over the phone in a minute or two.

Best thing about this new service is that you are never placed on hold and get to talk to real repairmen in the US.

Here's a link to this great service

Good luck!

Posted on Jan 02, 2017

Add Your Answer

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

1 Answer

Toro snowblower surges what could be wrong? Any help will be appreciated. Thanks


Try removing the needle from the carburetor and soaking it in brake fluid (and any other parts that may look suspicious) over night; clean and regap or replace spark plug; ...also, try using high test fuel.... this runs cleaner on my Toro826.

Jan 06, 2018 | Toro Garden

2 Answers

I put a mixture of oil gas in my 621 R/621 toro snowblower?


Hi Jerome:
Shouldn't be too bad.
You could disconnect the fuel line at the carb and drain the tank.
Drain and flush the carb. Reconnect the fuel line and fill with fresh gas.
If it won't start, pull the spark plug and clean/dry it with a propane torch, or replace it.
Odds are it will be fine.
Cheers.

Jan 18, 2016 | Toro Power Clear 621 R Snowblower - 38451

2 Answers

My toro snowblower will not start,with gas or starting fluid,no spark,stater rust cleaned off flywheel,carb cleaned,bench set,It fired with starting fluid ,but the carb had gunk in float bowl,what am


Clean out the float bowl as well clean out the fuel jet in the bolt that holds the bowl on. There usually are very small holes in this jet and if you can't see or blow through them you have to clean this out. Will not run if this is plugged. You can blow this out with an air com presser or a very small wire to push through it. Don't force anything through this hole or you could damage it. If it will start when you put a spoon full of gas in the spark plug hole and replace the plug and stalls in a few seconds it's usually a dirty carb or dirty jet. You can buy a cleanser as well to spray if needed.

Dec 26, 2014 | Toro Powerclear 221qe Electric Start...

1 Answer

Snowblower leaks gas on garage floor


Is it coming from the carb or tank? Either way replace the fuel lines, they crack an get pin holes in them an cause problems. If it comes from the carb get a rebuild kit an, very cheap, an replace the seals.

Feb 28, 2014 | Toro Powerclear 221qe Electric Start...

1 Answer

My toro snowblower keeps stalling. It starts up fine, but won't run continuously.


If you haven't already, dump out gas and put fresh in it and try this, if it doesn't work you will have to clean the carb, take it apart and clean all jets ports etc and put back together and you should be Good to Blow Snow, pretty common problem with Small Engines that set half the season.

Dec 04, 2011 | Garden

1 Answer

Toro snowblower wont start.I have a toro ccr powerlite that dosnt seem to be getting fuel from the fuel line into the carb. I took the fuel line off and fuel is getting to the carb so then i removed carb...


Reference the Toro snow blower. It may sound crazy but loosen the gas cap just a bit. I had the same issue with my snow blower and a friend gave me the solution. It works great now. Hope this works for you.

Oct 21, 2011 | Toro Lawn Mower With Toro Power Tools

1 Answer

I was given a Toro 521 Snowblower. It won't start. I replaced the plug, gas filter, air filter and gas line. Still won't start. Also drained the tank and added new gas


If you replace the carburetor needle seat and bowl gasket it will do the trick. Look up your model snowblower at www.arcolawn.com and you can have them shipped.
Good luck
joe

Feb 14, 2011 | Garden

1 Answer

Toro 521 snowblower instruction to replace belts


Remove bottom cover(4bolts) 3/8"Remove plastic housing cover (mine had 2 bolts)3/8"Loosen belt guide bolt.1/2" rotate guide away from belt.I used a pipe wrench to hold main shaft and removed drive pulley.Replace drive belt as you return pulley onto shaft.Replace auger belt.Align belt guidesSet handle adjustmentsReplace coversTest and hope for warm weather, I live in BuffaloHope this helps

Jan 01, 2011 | Washing Machines

Not finding what you are looking for?
Toro Blowers Rake and Vac - Electric Blower/Vac - 51573 Logo

1,996 people viewed this question

Ask a Question

Usually answered in minutes!

Top Toro Garden Experts

Joseph Mueller
Joseph Mueller

Level 2 Expert

346 Answers

roeb

Level 3 Expert

819 Answers

Marvin
Marvin

Level 3 Expert

85222 Answers

Are you a Toro Garden Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...