Taking roper washer apart.

They make them so that they are very difficult to get apart without special tools. You'll need a ''pump repair'' tech. They _do_ exist, but these days repair can cost more than ''replace.''

It _shouldn't_ be that way, but unfortunately that is the reality.

If you faucet is leaking, try this simple step to see if it will stop. First, turn the water supply line off under the sink. Next, open the valve that is leaking all the way open. Take a wrench and tighten the nut just below the faucet handle. Now turn the vale to off and open your supply line and then test the faucet again. What you are doing here is tightning the packing nut inside the faucet. Good luck.

This model is direct drive with a front mounted drain pump. The drain pump is THE most common leak location on these type washers! The pumps do NOT generally leak at the hoses, but from the impeller side between the pump and motor. There will be a telltale water mark on motor side of the pump shell.It can easily be fixed by popping the 2 retaining clips, removing the two drain hoses, and pulling off the old plastic pump, replacing it in the reverse order after cleaning the end of the motor shaft. Pumps run about 30 dollars. If you are sure this isn't the culprit, check for signs of leakage between the tub center and transmission, there is a tub gasket there. The tub itself, is not likey to leak, it is one piece with heat welded seams.Go to Youtube and search Whirlpool washing machine repairs, there are a number of instructional videos that show you exactly how to repair these machines and save yourself a lot of money. Incidentally Roper is built by Whirlpool, that's why I said search with that name.

Hope this sheds some light on the problem

kcomp1863

If you have a leak, the most common cause is a worn drain pump, leaking drain hoses or the hose to the air dome has come loose. You will need to remove the exterior case of the washer to be sure. DO NOT lay the washer on its back. The gearcase contains oil and it may leak through the breather hole.

The following link explains how to inspect your washer for leaks:

http://www.fixya.com/support/r3576648-washer_leak__top_loader

If the drain pump is leaking, it is not serviceable and must be replaced, the following link explains how to replace one:

http://www.fixya.com/support/r3794382-replacing_water_pump_whirlpool_top

Replacement parts (if required) may be purchased on line at any of the following websites:

searspartsdirect.com
pcappliancerepair.com
appliancepartspros.com
repairclinic.com

Prices vary between sites, so shop and compare.

Read through the instructions provided and let me know if you need further assistance. Please post back with a complete MODEL NUMBER so that I may be able to povide you with better assistance. I hope this help you.

NOTE: For future reference, if you would like to a have a complete repair manual for this model washer, Repairclinic.com has a one available for Whirlpool manufactured direct-drive washers (includes Roper) for about $20. The item number is 1170635.

It's in the drain hose somewhere,during the fill the water gets as deep in the drain hose as it does in the washer,during the wash the pump runs in reverse keeping the water level in the hose low,during the drain the hose is filled again.
Prop the washer up in front on a couple bricks or boards,start putting in water until it starts to leak and take a peak under the machine.

lean it back look st the pump if water on it take it off 2 clips hold it on and check seal looks bad? ...replace thumbs up

VE6GAR 73 88 99

defective pump...remove 2 screws on console corners..flip console back...disconnect lid swich harness,,,remove the 2 brass or gold color clips on each side,, now pull cabinet towards you..you see that plastic piece with 2 black hoses replace it...onthejob

I believe Roper washers are manufactured by Whirlpool. The following link should provide you with the necessary steps in removing the washer casing, so you can access the pump:

http://www.fixya.com/support/r397092-replacing_water_pump

If this information is not correct, or if you require additional assistance, please let me know. I hope this helps you.

ckd pump lean washer back against wall pump next to front ..2 clips hold pump to motor 2 clamps on hoses pump slides off motor ..also ckd hose from pump to drain underneath

replace pump it is all spin welded together and not made for repair besides you already have it off $45-50 will finish repair normally costing 150-200 for tech to do