This should help any further assistance please feel free to contact me.
WHIRLPOOL Range/Stove/Oven Fault Codes Non Y-Line
NOTE: Not valid for Y line. If there is a Y near the end of your model number, do not use this chart.
Failure
Code
Condition
Check/Repair
4 Digit Failure Code
F0 - E0
Analog to Digital Failure
Disconnect for 30 seconds - if display re-appears - replace control
F1 - E1
Safety flip flop
Replace Electronic Range Control/Clock (ERC)
F2 - E0
Shorted keypad
Replace Electronic Range Control/Clock (ERC)
F3 - E0
Oven temperature sensor or oven temperature sensor fuse opened
Replace oven temperature sensor or fuse
F3 - E1
Oven temperature sensor shorted
Replace oven temperature sensor
F3 - E2
Oven too hot
Replace oven temperature sensor
F3 - E3
Clean temp too hot
Replace oven temperature sensor
F5 - E0 F5 - E1 and E2
Check door/latch switch
Replace component
2 Digit Failure Code
F0 or F1 or F5
Failed transistor
Replace Electronic Range Control/Clock (ERC)
F2 - E0
Oven temp too high
1. Test operation of door lock on self-clean models
2. Test relay contact operation
3. High resistance in oven temperature sensor
F3
Open oven temperature sensor or thermal fuse
Replace oven temperature sensor or thermal fuse
F4
Shorted oven temperature sensor
Replace oven temperature sensor
F6
Problem in time keeping circuit
1. Reset time and/or cooking operation
2. Check for proper ground
F7
Stuck function switch or button on Electronic Range Control (ERC)
Replace ERC (Electronic Range Control/Clock)
F8
Failure Electronic Range Control (ERC)
Replace ERC (Electronic Range Control/Clock)
F9
Door lock circuit
Check wiring and test operation of door lock switch
WHIRLPOOLRange/Stove Oven Fault Codes, Common
Failure
Code
Condition
Check/Repair
Digit Failure Code2
F1
Analog to Digital Failure
Disconnect for 30 seconds - if display reappears - replace control board
F1
Safety flip flop
Replace board
F1
Shorted keypad
Replace keypad
F3
Oven temperature sensor opened
Replace oven temperature sensor
F2
Oven temperature sensor shorted
Replace oven temperature sensor
F3
Oven too hot
Replace oven temperature sensor
F3
Clean temp too hot
Replace oven temperature sensor
F5
Check door/latch switch
Replace switch if defective
4 Digit Failure Code
F1 - E1
Safety flip flop
Replace board
F2 - E0
Shorted keypad
Replace keypad
F3 - E0
Oven temperature sensor opened
Replace oven temperature sensor
F3 - E1
Oven temperature sensor shorted
Replace oven temperature sensor
F3 - E2
Oven too hot
Replace oven temperature sensor
F3 - E3
Clean temp too hot
Replace oven temperature sensor
F5 - E0 F5 - E1 and E2
Check door/latch switch
Replace switch if defective
Same problem, none of the controls for the oven, timer, etc will work.
E0-F2
My Sf cleaning oven will not come on. It dislays E1 F5
e1-f1 error message
Whirlpool Gold gastop range: E0 -F2- problem, and notify you when a new solution is offered.
Whirlpool Gold gastop range: E0 -F2- problem, and notify you when a new solution is offered.
Not happy this is the second time this has happened. First time it just corrected itself this time nothing and they tell me it is not covered by warrenty. Two year old heap of garbage!
Just replace all my component in the top due to the repair man told me it was a stuck key. over $300.00 for parts and still the dam thing won't work. Oven goes on for about 1 minute then shuts down and gives you the error code E-F2. Like mentioned before a piece of junk and now I am looking at having to buy another range. New parts what Else can be wrong.
Another downfall with the gas range is if the power goes off you Can not Even use th top burners to cook with which is one reason I went to the gas range since we loose our power a lot in our country..
Somehow a spider entered my stove and now lives behind the glass and in front of the clock! I think the little beggar shorted out the display and was hoping that she'd gone to that big Web in the Sky, because she wasn't in the usual place after the E0-F2 error started. But as I was pulling the stove away from the wall to disconnect the power she raced back to her original position. Little ****...
The disconnect/reconnect solution worked great, though!
×