I connected it to my TV but I could only hear the audio and it had no image or video

Here is the User Manual with instructions on all the different types of connection between TV and your Phonak:
https://www.phonak.com/content/phonak/us/en/hearing-aids/accessories/phonak-tv-link/_jcr_content/mainpar/downloads/productdownloadspar/download_1/file.res/User_Guide_TVLink_II_029-0313.pdf
And here the backside plugs on the Panasonic TV TC-L32C5/TC
http://hdtvparts.net/images/thumbs/0018428.jpeg


So you can use the Audio In or the RCA cable connection!
Hope it helps;)

This sounds like either a bad connector that is jarring loose on the video side or you are intermittently losing signal. Audio will go out before video on a bad signal. It requires more bandwidth.

Hello
You want to connect your TV with an external audio device, and want to hear sound from it, I assuses, and posts this solution.
There is audio out sockets at the back side of the TV, very near to S-Video socket. Marked audio "L" & "R". These two sockets are audio out socketsfrom TV to connect any external audio amp. Just use an audio cable to connect these sockets, to 'Audio IN' of the amp socket. Switch ON both the devices. You can hear the audio of your TV programmes by the amp you conneccted with.
The picture of the AV cable is given here. Take red and White colourd connections to connect the TV with amp. Left the Yello coloured pins free. It is meant for video.

Hi,
you have not stated whether you want to hear the sound on TV or Stereo Receiver..
Here are 2 possible solution for both alternative..
1. thru TV
Your VCR has either 2x Audio (red and whitw ) and 1x Video output (yellow) RCA jacks or a SCART jack on the back side..
you need to connect all 3xRCA jacks to your TV's respective input.(or SCART ) than you will manage to see both video and hear the sound by selecting the VIDEO input on the TV .
2.thru RECEIVER
.** you need to connect "Audio Output " RCA jacks of your VCR
** to "AUX input " or "DVD " OR "Any input" of your receiver ( except Phone )
** than just switch to respective mode on RECEIVER corresponding your RCA connection...
There you go..VCR sound on the Receiver..
*** pls remember you can connect VCR to either TV or Receiver to listen audio ,not both..the yellow RCA video output connection always goes to TV..

Hope this helps!..if more help requires pls let me know.
Take care and please Remember to rate/vote for us to continue for Helping out the Community :)

You will need to connect a RCA Audio Cable (see link to image below) from an audio output jack on the rear of your receiver to the audio input jack on your TV. Be VERY careful as to keep volume down as most all TV speakers are geared to take low inputs. With your 1000w receiver, it is always tempting to crank it up and end up blowing your speakers.

http://www.amazon.com/Belkin-PureAV-RCA-Audio-Cable/dp/B00022TN86

Well you can just use the hdmi cable if you're going both audio and video in to your tv. With your hdmi cable you get the best quality for both.

But in anycase, it seems that your PS3 is set up to output video via HDMI cable. To reset our video output settings, simply power down your PS3 (turned off) and hold down the power button until you hear the second beep. (around 5-10 secs) Power back up and hopefully you'll have video via your av cable. Hope this helps.

Verify this is a Pioneer VSX-1018AH.

The manual explains it all... The problem is probably an incompatible setting on your source.

Search for "not support" in the manual...

http://www.pioneerelectronics.com/PUSA/Unassigned+Content/VSX-1018AH-K+OPERATING+INSTRUCTIONS

I think this may do it... From Page 86...

No picture or sound. • This receiver is HDCP-compatible. Check that the components you are connecting are also HDCPcompatible.
If they are not, please connect them using the component or composite video jacks.
• Depending on the connected source component, it’s possible that it will not work with this receiver
(even if it is HDCP-compatible). In this case, connect using the component or composite video jacks
between source and receiver.
• If the problem still persists when connecting your HDMI component directly to your monitor,
please consult the component or monitor manual or contact the manufacturer for support.
• If video images do not appear on your TV or flat panel TV, try adjusting the resolution, DeepColor
or other setting for your component.
• If ‘NOT SUPPORT’ appears in the receiver’s display, try adjusting the resolution, DeepColor or
other setting for your component.
• While analog video signals are being output over HDMI, use a separate connection for audio
output.
• When this receiver reproduces MULTI CH IN audio sources with the HDMI setting set to
THROUGH, you cannot hear audio output from all channels. In this case, make a digital or analog
audio connection.
• To output signals in DeepColor, use an HDMI cable (high speed HDMI cable) to connect this
receiver to a component or TV with the DeepColor feature.

Check the HDMI Control (Page 65-66 of the manual). It only works with Pioneer Flat Panel TV's. Also check Page 83 for "No image is output..."

No image is output when an
input is selected.
• Check the video connections of the source component (see page 18).
• For high-definition video (using component video connections), or when digital video conversion
is switched off (in Setting the Video options on page 72), you must connect your TV to this receiver
using the same type of video cable as you used to connect your video component.
• Make sure the input assignment is correct for components connected using component or HDMI
cables (see The Input Setup menu on page 67).
• Check the video output settings of the source component.
• Check that the video input you selected on your TV is correct.
• Some components (such as video game units) have resolutions that may not be converted. If
adjusting this receiver’s Resolution setting (in Setting the Video options on page 72) and/or the
resolution settings on your component or display doesn’t work, try switching Digital Video
Conversion (in Setting the Video options on page 72) OFF

Double check the way you've got the cables connected.  Audio but no video generally means that the yellow video cable isn't hooked up correctly.
Check to make sure the video cable (yellow) is hooked up to the same input on your television that your audio (red and white) cables are.

press and hold the power button for at least 5 seconds until you hear a 2nd beep.
this should reset your settings and the video/audio will autoconfigure if you have HDMI. if you have another type of connection, use the setting under video settings and adjust them to 720p.

did you hook the yellow up to a green jack labeld Y on the back? What kind of tv do you have? Some component inputs (the ones with the green Y jack) are not compatible with the video input you have, some are.