2610 unhoked my 2610, hooked in another printer it was bad so hooked back up my 2610 now it will not print from my printer!1

Try to turn your Windows Firewall OFF. If you can now print to the printer, just turn your Firewall back ON but add an exception to the HP printer.

The font size is set in your printing/ viewing software and not the printer. If it's Adobe you open the document and make changes before printing. If it's an internet document you need to resize in the internet tools section.

For products with keypads on the control panel:
1. Without turning the unit off, unplug the power cord from the back of the product.
2. Press and hold “# and 6′ keys.
3. While holding those keys plug the power cord back in.
4. Wait until the screen goes blank before you release those keys.
5. Follow on printer screen instructions.
For Box-type models:
1. Unplug the power cord from the printer.
2. Wait for 30 seconds.
3. Plug the power cable back in the printer and turn it on.

HP Photosmart 2610 All in one Ink Jet Printer
I can only print, message says scanner failure turn powere off and on , I do this and it does does not reset

Print cartridge
When the print cartridge contacts are dirty and the printer cannot detect/communicate with print cartridge.
Clean the contact points on the cartridges with a dry, lint-free cloth.
1. Open the top cover of the printer.
2. Remove the print cartridges.
3. Clean the copper-colored contact points on the cartridges with a damp, lint-free cloth. Use a dry, lint-free cloth to remove moisture from the contacts.
5. Insert the cartridges back into the printer.
6. Close the top cover.
7. Try printing again.
If you still cant communicate try with new cartridge .

0x error codes indicate that the product has an internal error. Try to reset the printer:

1. Without turning off the product, disconnect the USB cable from the rear of the product.
2. Remove the cartridges from the product.
3. Wait for the 'Insert Cartridges ' message to display on the control panel.
4. Disconnect the power cord from the back of the product.
5. Wait 60 seconds.
6. Reconnect the power cord. If the product does not automatically turn on, press the Power button
7. Reinsert the cartridges, and then close any open doors on the product
8. If you receive a prompt to print a calibration page, do so.
9. Reconnect the USB cable to the rear of the product, and then try printing again.

Try cleaning the gold contacts on cart first, with distilled water. Let dry and try again.
If not, try this one
1.Try placing sheet of black text on copy board, and run many copies black only. I ran 25x12 times still no black. Run head clean after about each 50 sheets. Persevered and finally BLACK ink OK
Inkypete

http://www.hp.com/#Support

Follow the link and get the correct driver and get installed

By self-test, I assume you are doing that manually on the printer. drivers downloaded/installed? right click on my computer, left click on properties, click on hardware, and then click on device manager. is there a yellow question mark by print drivers? If so, then need to load them from the internet or from your installation disk.

Try these steps from HP

http://h10061.www1.hp.com/ccsearch/search?method=mainQuery&qry=carriage+jam&pname=HP+Photosmart+2610+All-in-One&ptype=consumer&stype=pn&spname=HP+Photosmart+2610+All-in-One&spid=421139&productBigSeriesOid=391113&pid=391116&temp_hql=s-001%2Cs-002%2Cs-004%2Cs-003%2Cs-005%2Cs-006%2Cs-017%2Cz-001%2Cc-002%2Cc-001&lang=en&ctry=us&dlc=en&mode=lz&uqry=&pname_desc=HP+Photosmart+2610+All-in-One+PSC+Printer%2FFax%2FScanner%2FCopier