Hi i want to know all the specs of this amp, i have one but i don,t have any info, so i would like to get some info like response at 2 ohms and 4 ohms with 12.5 volts and 14.4 volts etc. any info would be nice thanks..ph2d..

If it doesn't say call the mafactor

Your ohm meter will not give you an accurate reading on a speaker.
It looks like the PL-300 is at lowest, 4 ohm stable. If it is a 2 channel amp (which
I believe it is) drive each speaker with a separate side (Left and Right).
You may damage the amp if you parallel or series the speakers.
7Here is a great site for all electronics info. See #57 on the right side pane for more speaker info.
Basic Car Audio Electronics Site

From the specs this amp can only handle 4ohms when bridged but can handle 2ohms when it's not bridged

Specifications

• Continuous Power (20Hz-20kHz, 0.04% THD)
  • 2 ch: (4 Ohm) 100Wx2
  • 2 ch: (2 Ohm) 200Wx2
  • 1 ch: (4 Ohm) 400Wx1
• Maximum Power (EIAJ)
  • 2 ch: (4 Ohm) 250Wx2
  • 1 ch: (4 Ohm) 750Wx1
• Frequency Response: 10Hz - 50kHz (0,-1dB)
• Total Harmonic Distortion: <0.01% (1kHz, 4 Ohm)
• Signal-to-Noise Ratio: >105dB (IHF-A Weighted, at 1kHz)
• Dimensions: 10-3/8" x 2-1/2" x 13-5/8"

Hope that helps.

This could be the reason. If you look at the specs for this amp you will see that the continuous power out is rated for 380W bridged. The speakers rated at 450W should be able to handle close to 315W continuous. Now if you split these numbers being you have bridged these speakers, you drive each one up to about 190W continuous. The speakers are being driven approximately by 60% of the rated capability. I personally like to keep it right where you got it, not exceeding 80% of the speakers rated capacity.

Here are the specs for the AMP:

Specifications

Peak Music Power 760 Watts

Number of Channels 2

Load Impedance Capability 2~8 Ohm (Stereo), 4~8 Ohm (Bridged)

Continuous Power (4 ohm) 125W x 2

Continuous Power (2 ohm) 190W x 2

Continuous Power Bridged (4 ohm) 380W x 1

Frequency Response 10Hz ~ 50kHz

Total Harmonic Distortion 0.008%

Signal-to-Noise Ratio 100dB

Dimensions 12" x 2-3/8" x 12-3/4"

Features

Bridgeable

Channel # Capability 1/2/3

PWM Regulated MOSFET Power Supply

Screw-Type Speaker Terminals

Balanced Isolator Input Circuit

RCA Inputs 2 Channel

Input Level Control Hi-Volt (200mV ~ 6.5v)

Built-in Crossover Selectable LPF (80Hz, -12dB/Oct.)

You can use any type of amp as long it can drive at least 1000 watts and it 2 ohm, 4 ohm or 8 ohm stable.Here is the specs on the woofer:

• 12" High Performance Subwoofer
• Rubber Seal Gasket
• High Temperature 2" 4 Layer Voice Coil
• Air Vented Aluminum Fomer
• Dual Voice Coil ( 4 ohm + 4 ohm)
• Large Foam Edge Surround
• Bumped Plated For Maximum Excursion
• Excellent For Sealed and Bandpass Enclosures
• 70 Oz Magnet Structure
• 1000 Watts Max
• Frequency Response: 25Hz-800 Hz
• 2 Ohm / 4 Ohm/ 8 Ohm Operation
• Screw Block Terminal

Also check this website for how to wire it to 2, 4 or 8 ohms: http://www.bcae1.com/spkrmlti.htm

Is the speaker a dual voice coil speaker? If so you can wire it up a couple of diferent ways, go to rockfordfosgate.com they have a woolfer wiring wizard that can show you the different ways to wire for 8 ohm.....4 ohm.....2 ohm....and 1 ohm...I would figure out how to get the most power out of the amp in mono mode, take that ohm load from there and see if you can wire your speaker to match it.

thats easy if you have posted the specs of amp and sub.are subs 1 2 4 ohm? what is the power rating of both amp and subs in 1 2 4 ohms.u need to post some info to get help.:]

Here are some specs:

4800W Max, High-Current 2-Channel Car Amplifier

RMS Power Rating:

• 300 watts x 2 chan. @ 4 ohms
• 600 watts x 2 chan. @ 2 ohms
• 1200 watts x 2 chan. @ 1 ohm
• Bridged:
  • 600 watts x 1 chan. @ 4 ohms
  • 1200 watts x 1 chan. @ 2 ohms
  • 2400 watts x 1 chan. @ 1 ohm

Max Power Output: 4800 watts @ 1 ohm

this is the web site I got the specs from

http://www.sonicelectronix.com/item_61_Audiobahn+A2300HCT.html

Hope this Helps...

ECLIPSE makes a 32440

If this is the amplifier you are looking for specs on...


4 x 85W @ 4 ohms (13.8V - 0.1% THD)
4 x 120W @ 2 ohms (13.8V - 0.1% THD)
2 x 240W @ 4 ohms bridge (13.8V)

Thanks for using FixYa -a FixYa rating is appreciated for taking the time to answer your Question.

The XM-1002HX is a two-channel amplifier with power ratings of 100 watts x 2 or 280 watts x 1 into 4 ohms and 140 watts x 2 into 2 ohms. ...