How can I fix a C3 error on my Dishwasher.
My dishwasher is AEG OKO_favorit 50700 , I asume its the same as the 50730W.
I need a repair manual?
Tokkie in South Africa [email protected]
AEG 50700 sensorlogic stops mid cycle with a C3 error code showing. The machine will still be making a noise as if trying to do something but won't switch off at the machine - only at the wall socket. I have cleaned the filters and putlet hose.AEG 50700 sensorlogic stops mid cycle with a C3 error code showing. The machine will still be making a noise as if trying to do something but won't switch off at the machine - only at the wall socket. I have cleaned the filters and putlet hose.
AnonymousDec 23, 2008
There is a water leak, level switch in base
There is a water leak, level switch in base
AnonymousMar 14, 2014
2 button timer switch for Salton SDW12 Dishwasher in South Africa.2 button timer switch for Salton SDW12 Dishwasher in South Africa.
You can't post conmments that contain an email address.
- If you need clarification, ask it in the comment box above.
- Better answers use proper spelling and grammar.
- Provide details, support with references or personal experience.
Tell us some more! Your answer needs to include more details to help people.You can't post answers that contain an email address.Please enter a valid email address.The email address entered is already associated to an account.Login to postPlease use English characters only.
Tip: The max point reward for answering a question is 15.
If the END or DRYING indicator on the programme progress display is flashing, you can probably rectify the fault yourself.
After rectifying an END or DRYING fault, press the button for the wash programme that has been started.
The wash programme continues. If the fault is displayed again, than check water leakage in the battom of dishwasher.
Malfunction: END and DRYING on the programme progress display are flashing simultaneously. Possible causes: The leak prevention system has been triggered. Remedy: Try to find and repair water leakage otherwise close the tap and call customer service.
I have a similar issue on oko favorit 50700. I have checked the flow from the inlet hose into a bucket and it really seems ok, so I think maybe a problem at the inlet to the machine? Plea update if you get a fix!
This is typical of a water leak onto electrical connection OR the electrical element has shorted internaly . Check this with a Ohm meter and itshould show the problem
Just pulled machine right out, tipped it over on the side, couldn't see anything obvious or a way "in", so re-positioned it - switched on - error message gone and all working fine !!?!
This seems like the anti flood system (polystireen float / micro switch) at the base of the washer is triggered,\. This puts the washer in pump out mode and stops inlet of water via the inlet solinoid. Dry the water on the base and then check for any water leaks. (pipe leak
C3 error means that there is water at the bottom of the dishwasher. Unplug the dishwasher, slide it forwards and push it back. So it stands on the 2 back knobs. Do this atleast at a anle of 45 degrees. You will see water flowing at the floor.
If this happens often you have a leak somewhere. Time to cal the technician then.
If you open a sidepanel and look at the bottom of the machine you see a brown device with a piece of white foam,this is the leak prevention system.
Push foam down and the error code should be cleared.
Make sure you there's no water left on the bottom of machine
AEG 50700 sensorlogic stops mid cycle with a C3 error code showing. The machine will still be making a noise as if trying to do something but won't switch off at the machine - only at the wall socket. I have cleaned the filters and putlet hose.
There is a water leak, level switch in base
2 button timer switch for Salton SDW12 Dishwasher in South Africa.
×