What is Error 20501 for a Oce Plotwave 500? - OCE Office Equipment & Supplies

This article is about two printer error codes, 22551 and 22531. These codes are associated with the OCE Plotwave 345 printer. The error code 22551 means that the printer has lost its connection to the computer, and the error code 22531 means that there is a communication problem between the printer and the computer.

this error more related to software problem,but you need do below step to check their hardware is in good condition.if all ok no problem,you may need to reformat their OS
1.off machine/on machine
2.pls check their controller connection (in you left side back cover down area).Make sure all the port are plug in properties and also in correct location,you cannot plug in to anywhere if no you will get the error code.
3. open fusing door ,try to unlock screw on right side back cover got 3 screw (torx 15 or 20)
4.open that cover look down that area got 1 big spider board.make sure all their connector usb port are plug in properties and in correct location.
5. check the big board should be got 3 LED green light stable on if no use machine.no got red LED on.
6.check that small board are properties install in good position in big board location.
7.check that small board must go 1 LED green light always falshing or stable,if got Red LED light on means this board faulty need replace new unit.

This error more related to software problem,but you need do below step to check their hardware is in good condition.if all ok no problem,you may need to reformat their OS
1.off machine/on machine
2.pls check their controller connection (in you left side back cover down area).Make sure all the port are plug in properties and also in correct location,you cannot plug in to anywhere if no you will get the error code.
3. open fusing door ,try to unlock screw on right side back cover got 3 screw (torx 15 or 20)
4.open that cover look down that area got 1 big spider board.make sure all their connector usb port are plug in properties and in correct location.
5. check the big board should be got 3 LED green light stable on if no use machine.no got red LED on.
6.check that small board are properties install in good position in big board location.
7.check that small board must go 1 LED green light always falshing or stable,if got Red LED light on means this board faulty need replace new unit.

Extreme Toner Low ADC. If you filled up the toner and this still doesn't work, it could be a whole list of other smaller components that would require a whole lot of explanation and instruction to remove safely. Its best to call an authorized Oce service technician to check this out.

Oce (Canon) makes 3 different types of "500" plan printers. The ColorWave 500, the PlotWave 500 and the old TCS 500. If you mention the proper model number you might get a faster answer. If you have the TCS500 this is a head calibration error. Was a printhead recently replaced? If so it is more that likely that either the plastic seal was not completely removed from the new printhead, or there may be some ink on the contacts on the inside of the printhead socket. Reinsert the printhead in question, and see if this solves the error. Power down the printer and unplug it from the wall. Clean the inside of the printhead socket with a long swab and some isopropyl alcohol. Plug in and power on the printer after replacing all printheads. On extremely rare occasions brand new printhead do fail, so if you have determined you might have a faulty printhead, replace it with another.

Hi i have a problem with oce plotwave 360 give me an error (NO COMMUNICATION WITH CONTROLLER - 95) please help me wath i need do

Fuser NTC 1 not working properly. Replace.

Error 08130 Fuser temperature protection circuit failed. This could be the Spider PBA or it could be the connections to the fuser itself.
Best to call an authorized service rep.

JAI UN PROBLEME AU PLOTWAVE 300 MARQUE OCE
CODE ERREUR 8510
C QUOI LE PROBLEME ET C DU A QUOI ET QUESQUE JE DOIT CHANGER
MERCI
REPONDEZ PAR EMAIL
[email protected]