Question about Garden

Open Question

How do you hook the throttle linkage to the carberator on 2050 johnsered ?

Posted by on

Ad

5 Suggested Answers

6ya6ya

6ya staff

  • 2 Answers

SOURCE:

Hi there,
Save hours of searching online or wasting money on unnecessary repairs by talking to a 6YA Expert who can help you resolve this issue over the phone in a minute or two.

Best thing about this new service is that you are never placed on hold and get to talk to real repairmen in the US.

Here's a link to this great service

Good luck!

Posted on Jan 02, 2017

Ad

Ted Schore

  • 7353 Answers

SOURCE: need to hook up the throttle cables to the

Usually if you look at how they clip on to the bracket, they only go 1 way.

Posted on Dec 18, 2009

Ad
wadingriver

wadingriver

  • 2223 Answers

SOURCE: I have a new carberator for model # 331777 1372

It might just be a single idle screw to adjust.. not familiar with the Model.

Posted on Sep 16, 2013

emissionwiz

Marvin

  • 85206 Answers

SOURCE: huskee riding mower missing linkage from throttle to carberator

Contact a retailer of mower for parts, we do not sell parts here.

Posted on Nov 18, 2016

Bill Boyd

  • 53755 Answers

SOURCE: I have a Poulan lawn tractor, Model # PB22H46YT. I can't get the linkage set properly along with the governor linkage? I've been looking for picture of carberator throttle and the governor setting

the throttle linkage and governor setting will be found in the workshop manual for the engine that you have
so
search --workshop manual for ( engine make and serial /model number) and down load the pdf version

Posted on Jun 28, 2018

Add Your Answer

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

1 Answer

Cleaning carberator


There are various way to clean your carburettor:
First, buy a can of carb cleaner spray.
Start your engine.
[1]: Remove air filter and squirt cleaner into venturi, revving engine via throttle linkage (at carb) to avoid stalling.
[2]: Remove fuel inlet hose from carb and squirt cleaner directly into inlet.

Otherwise:
[3]: If very dirty, the carb may need to be removed by a mechanic and sent in to a professional company for service.

Jul 25, 2018 | Cars & Trucks

1 Answer

I have a Poulan lawn tractor, Model # PB22H46YT. I can't get the linkage set properly along with the governor linkage? I've been looking for picture of carberator throttle and the governor setting


the throttle linkage and governor setting will be found in the workshop manual for the engine that you have
so
search --workshop manual for ( engine make and serial /model number) and down load the pdf version

Jun 28, 2018 | Poulan Garden

1 Answer

Huskee riding mower missing linkage from throttle to carberator


Contact a retailer of mower for parts, we do not sell parts here.

Nov 18, 2016 | Garden

1 Answer

Connecting carburetor to the throttle on husqvarna 44 chainsaw


The wire linkage has a short Z bend in one end this hooks into the throttle lever from the outside, the other end has a long loop this goes into the trigger arm from the outside, you will need to twist the top of the trigger arm slightly to allow the linkage to go into the hole in the trigger arm.

Dec 29, 2017 | Husqvarna , No.455 Rancher, 20" Gas -...

1 Answer

I need the linkage diagram for a 20 hp briggs and statton model 407777-0167


Besides the service manual you can view parts diagrams at a dealer like www.arcolawn.com. You can purchase the service manual at a dealer and it will show you how to hook it up.
The throttle linkage hooks up to the throttle shaft closest to the engine. the governor spring attaches the governor arm to the throttle linkage.
The choke cable attaches to the shaft farthest from the engine. I hope this helps.
PS your engine has two factory service bulletins on it.
Joe

Feb 15, 2011 | Briggs & Stratton Briggs Stratton Intek V...

1 Answer

Can not get lawn tractor to idle in the high setting. Think it may be the carberator. How do I clean it and the throtle body?


Go to an automotive parts store a get a can of GUNK spary carb cleaner. Spray directly into the carb and spray the throttle linkage as well. This will loosen any junk that's causing sticking.

Sep 17, 2010 | Garden

1 Answer

Car wont idel and revs some times for no apparent reason its a hyundai xl 1995 duz it sound like the iac valve


If it has a carberator check to make sure that the throttle linkage is in a relaxed position when the car should be idoling in other words if the linkage is too tight then while your gas pedal may not be pressed the linkage is so tight that it is still pully on the throttle linkage and causing it to rev. The only reason i can think of it revving on its own though is maybe a tension spring on this linkage is broken and the linkage is loose and flopping back and forth from idel to throttle with bumps and other distrubances.

Aug 04, 2009 | 1994 Hyundai Excel

1 Answer

I have an onan 2800 gen that will not charge


If the govenor didn't work that means that you placed the linkage on the carberator the wrong way. This will cause the genset to overspeed and possibly stop the genset from creating voltage. If the genset does not create voltage then you won't have a charger. Fix the linkage first by looking to make sure that the throttle plate is closed before starting genset. Once you start the genset check for voltage.

Apr 12, 2009 | Watts Onan Portable Generator - 4000 ,...

Not finding what you are looking for?
Garden Logo

Related Topics:

32 people viewed this question

Ask a Question

Usually answered in minutes!

Top Garden Experts

roeb

Level 3 Expert

819 Answers

john h

Level 3 Expert

22486 Answers

Marvin
Marvin

Level 3 Expert

85206 Answers

Are you a Garden Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...