Question about Kenmore Washing Machines

Open Question

Sears Kenmore series 200, How do I remove the agitator?

Posted by on

Ad

6 Suggested Answers

6ya6ya

6ya staff

  • 2 Answers

SOURCE:

Hi there,
Save hours of searching online or wasting money on unnecessary repairs by talking to a 6YA Expert who can help you resolve this issue over the phone in a minute or two.

Best thing about this new service is that you are never placed on hold and get to talk to real repairmen in the US.

Here's a link to this great service

Good luck!

Posted on Jan 02, 2017

Ad
aborcass

Ron Coons

  • 2651 Answers

SOURCE: model 80 Sears Kenmore washine(Remove inner basket)

under the agitator youll see a lock nut appox 2-3in, around "locking" the inner basket to the outer basket. although they do sell a spanner wrench to remove this nut, A decent pipewrench and little muscle will get it loose, after that the tub will pull right out. assuming youve taken off the outer tub gasket cover

Posted on Mar 10, 2008

Ad

Bill Dozier

  • 262 Answers

SOURCE: Remove agitator on Kenmore 90 series

ok take the top off the agitator there is a cap carefully remove this cap and then some have a inner cap with a handle remove that also in side the agitator it has a 1/2" or 7/16" head bolt remove the bolt and then pull up really ******* the agitator. to replace dogs you have to break the taps holding them in not the agitator be careful
'

Posted on Jan 11, 2009

TheMobilian

Dan Webster

  • 8220 Answers

SOURCE: 70 series kenmore washer won't agitate help model #82873120

No wash, no spin read THIS
Spins, pumps, won't agitate right: check THIS out


If you need further help, reach me via phone at https://www.6ya.com/expert/dan_73bbd84fe1d95b61

Posted on Mar 27, 2009

Anonymous

  • 1 Answer

SOURCE: Sears Kenmore 80 series washing machine Model 110.26832691

How do you remove the top of a kenmore washing machine? I have a mouse stuck in the lid and can not get the top off.

Posted on Apr 30, 2009

Maytag317

Victor

  • 1136 Answers

SOURCE: replacing the agitator dogs in a Kenmore 80 series washer

Hi, Remove the cap on the agitator and then remove the inside cover. There is a 7/16" bolt under the inside cover. Remove the bolt and the agitator will lift out. Seperate the 2 pieces of the agitator and replace the dogs. You might have to use a flat blade screw drive and punch out the 4 tabs around the bolt hole in the agitator if this applies.
I hope this helps you. Please let me know if I can assist you further.

Vic

Posted on Jul 03, 2009

Add Your Answer

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

1 Answer

The agitator is slipping on our Kenmore 80 series toploader. I'm not sure how to remove it.


This assumes that you have a basic Kenmore / Whirlpool top load, direct drive, neutral drain (it doesn't spin until the pump removes most of the water) machine.

First, see the Sears parts site for your washer:
http://www.searspartsdirect.com/partsdirect/index.action

Enter your model number (###.######) and you'll see a list of major sub-components with diagrams and parts.

Look at the section on the Sears site for Agitator, basket and tub.

Assuming that only the top section of the agitator is "slipping, the problem points to the Agitator "Dogs"

See the following for how to replace them.

http://www.american-appliance.com/catalog/newsdesk_info.php?newsPath=16&newsdesk_id=136&osCsid=8878c06f855a89c90959d53553cf9ab8

If it's not the "Dogs" see the following that has a section on how to remove the agitators and check the splines.

http://www.american-appliance.com/catalog/newsdesk_info.php?newsPath=16&newsdesk_id=137


Mar 02, 2010 | Kenmore Washing Machines

1 Answer

Washer now agitating lazily. Ken. HD 60 series. Agitator doesnt seem to be fully connected? How do you remove the agitator?


This assumes that you have a basic Kenmore / Whirlpool top load, direct drive, neutral drain (it doesn't spin until the pump removes most of the water) machine.

First, see the Sears parts site for your washer:
http://www.searspartsdirect.com/partsdirect/index.action

Enter your model number (###.######) and you'll see a list of major sub-components with diagrams and parts.

First, I'd pull the agitators and check for worn or damaged splines inside the agitator or on the agitator shaft.

Following is a description of how to take them out.

http://www.american-appliance.com/catalog/newsdesk_info.php?newsPath=16&newsdesk_id=137

I'd also check the Motor Coupler for a worn center rubber piece.

Jan 16, 2010 | Kenmore Washing Machines

1 Answer

Series 80 Agitator top dosent work


If the bottom agitates and not the top, the problem is likely the 4 "agitator dogs" designed to allow the top agitator to turn only one way.


I assume that your model number starts with a 110 instead of 100.

First, see the Sears parts site for your washer:

http://www.searspartsdirect.com/partsdirect/getModel!retrieve.pd?modelNumber=110.26842692

Look at the section on the Sears site for Agitator, basket and tub.

See the part "Dog, agitator "

Remove the fabric softener unit, lift the top agitator cap (use a screwdriver) and you should see a plastic part in the center of the top agitator with a 1/2" square drive.

Remove the drive and lift off the top agitator. Turning it over you should see the 4 "dogs", replace these and the top agitator should turn in one direction only.

Replace the 1/2" drive, the cap and fabric softener unit and the top agitator should work.


Following is an illustrated description of the above.

http://www.american-appliance.com/catalog/newsdesk_info.php?newsPath=16&newsdesk_id=136&osCsid=0da65cea0e338fe930b1fde153a243f0


Jan 09, 2010 | Kenmore Washing Machines

1 Answer

The upper portion of the agitator (Kenmore Series 80 top load)stopped spinning as if the thread has stripped. What parts need to be replaced?


This assumes that you have a basic Kenmore / Whirlpool top load, direct drive, neutral drain (it doesn't spin until the pump removes most of the water) machine.

First, see the Sears parts site for your washer:
http://www.searspartsdirect.com/partsdirect/index.action

Enter your model number (###.######) and you'll see a list of major sub-components with diagrams and parts.

Basic top load, direct drive Whirlpool / Kenmore washers with two piece agitators use "agitator dogs" to allow the top section of the agitator to turn in one direction only.

These are plastic pieces and over time can wear.

See the following for how to replace them.

http://www.american-appliance.com/catalog/newsdesk_info.php?newsPath=16&newsdesk_id=136&osCsid=71493d5cab3d7784ad8aa7cde8e5e5d4


Nov 17, 2009 | Kenmore 24032\24036 Top Load Washer

1 Answer

Dual action kenmore 70 series washer need to remove agitator


First, see the Sears parts site for your washer:
http://www.searspartsdirect.com/partsdirect/index.action

Enter your model number (###.######) and you'll see a list of major sub-components with diagrams and parts.


It sounds as if your "Agitator Dogs" are damaged or broken. These are plastic pieces that allow the top agitator to turn only one way.

Please see the following for how to access and replace them if necessary.


http://www.american-appliance.com/catalog/newsdesk_info.php?newsPath=16&newsdesk_id=136&osCsid=39649e541343127154c647348d1156d9

Basically,

1. Remove the fabric softener dispenser.

2. Using a short flat blade screwdriver, remove the cap.

3. You may see a 1/2" square plastic nut.

I've used a 1/2" extension for a socket set to remove the nut.

4. Pull the top agitator off and turn it over carefully.

You should see the agitator dogs (per the illustrations).

Replace them if necessary and re-mount the agitator, tighten the bolt carefully, put the cap and fabric softener dispenser back on and the top part of the agitator should only turn one way.


Nov 06, 2009 | Kenmore Washing Machines

1 Answer

Bottom part of agitator does not work, i replaced the clutch dogs two weeks ago for the top part. kenmore series 80


This assumes that you have a basic Kenmore / Whirlpool top load, direct drive, neutral drain (it doesn't spin until the pump removes most of the water) machine.

First, see the Sears parts site for your washer:
http://www.searspartsdirect.com/partsdirect/index.action

Enter your model number and you'll see a list of major sub-components with diagrams and parts.

There are a number of Series 80 design washers. You'll need the actual model number to better check for the problem.

First, I'd remove the top agitator (as you've already done), then I'd remove the main agitator.

Under it you will see a clip and what Whirlpool calls a "washer". The "washer has two prongs, one fits into the main agitator shaft drive and the other fits in the lower agitator. If one or the other of the prongs is broken, the agitator most likely wont. I'd also look inside the main agitator to see if the ridges are broken off.

I'd then start the washer on it's smallest cycle and see if the main agitator shaft turns back and forth. If it doesn't and the washer goes through it's drain and spin cycles, the problem is likely in the transmission itself with what they call the agitate gear and / or agitate cams.

Please see the Whirlpool / Kenmore PDF document on installation, maintenance and operation of direct drive washers.

https://secured.whirlpool.com/Service/SrvTechAdm.nsf/2cd44500d572193285256a45004fd9d6?OpenView&Start=1

This is a Whirlpool document with parts lists for their commercial washers (basically the same as the consumer models)

If the problem is in the transmission, although it looks complicated, it really isn't that bad if you have a moderate level of mechanical ability.




Sep 26, 2009 | Kenmore 22422 Top Load Washer

1 Answer

Agitator: bottom moves, top does not


If the bottom agitates and not the top, the problem is likely the 4 "agitator dogs" designed to allow the top agitator to turn only one way.

On the Sears parts site:

http://www.searspartsdirect.com/partsdirect/getModel!retrieve.pd?pop=true&modelNumber=110.26902691&pop=flush

replace the 110.26902691 with your model number (lift the lid and the model number should be printed on the cabinet) and look at the section on the Sears site for Agitator, basket and tub.

This is what they look like:

pd_26_110_80040?$pddetailsth$ #21 on diagram Dog, agitator (4) Number:3366877Substitution:80040 $9.25Remove the fabric softener unit, lift the top agitator cap (use a screwdriver) and you should see a plastic part in the center of the top agitator with a 1/2" square drive.

Remove the drive and lift off the top agitator. Turning it over you should see the 4 "dogs", replace these and the top agitator should turn in one direction only.

Replace the 1/2" drive, the cap and fabric softener unit and the top agitator should work.

Sep 13, 2009 | Kenmore 23822 Top Load Washer

1 Answer

I have a sears Kenmore series 80 and the agitator doesn't work very well. It sounds like something is almost broken in the top of the agitator itself. How do I remove the agitator to find the problem.


If the top portion of the agitator (called the "auger") is no longer spinning like it should, you may have worn agitator dogs. The following link explains how to access and replace them:

http://www.fixya.com/support/r823955-replacing_agitator_dogs

This is a very simple an inexpensive repair. The part number is included in the link I provided. If this does not correct your problem, or if you have any questions, please let me know. I hope this helps you.

Jul 09, 2009 | Kenmore 22422 Top Load Washer

Not finding what you are looking for?
Washing Machines Logo

Related Topics:

44 people viewed this question

Ask a Question

Usually answered in minutes!

Top Kenmore Washing Machines Experts

fordexpert

Level 3 Expert

5692 Answers

Harvey Mahal

Level 2 Expert

39 Answers

Kristen Denison
Kristen Denison

Level 1 Expert

13 Answers

Are you a Kenmore Washing Machine Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...